PDA

View Full Version : P-Pump 24Valve

Pages : 1 2 3 [4]
  1. Trans issues
  2. Tach sensor mounting
  3. vp timing case mods for p pump
  4. John deere injectors
  5. Jumpy, touchy throttle, can't tow
  6. Where to buy a spacer for intake??
  7. Gathering up some parts, need some help!
  8. 24v Ppump twins in Destroked dually
  9. 01-02 Cruise Control!!!
  10. Oil breather pics
  11. Leaky Lines
  12. 6.7 crosstubes in VP head
  13. E.d. S300 66/74
  14. At what level does the 160 pump struggle?
  15. Voltage on ppump TPS
  16. Truck Low On Power? Advice?
  17. any opinions on compound setup
  18. thoughts turbo/ injectors. running hot.
  19. Shutoff Solenoid Woes
  20. Which engine is used to make 24valve P pumps?
  21. Pistons
  22. 24v p pump 20 over pistons
  23. 800 HP best cam for single charger?
  24. Fuel milage
  25. 0 fuel pressure ppump
  26. Porting/polish
  27. looking for p pump
  28. p pump 24v 2001 rough idle when warm miss light throttle
  29. What single to choose
  30. Can't seem to make any power???
  31. p pump w/common rail head
  32. My headache build
  33. conversion complete bad pump maybe?
  34. fuel return
  35. Lift pump
  36. Need cross over tubes asap!!
  37. help me critique my build
  38. tired of the solenoid leaning toward a cable
  39. New turbo still no power
  40. 800hp 24v setups
  41. Cam Sensor Wiring Diagram
  42. Fueling issues
  43. Timing vs. head gaskets
  44. Pump identification
  45. ?'s on running s400 single
  46. Ppump 6.4
  47. Engine dies after 4k rev
  48. advice needed
  49. Interesting fuel line routing?....
  50. Who bends CPP lines?
  51. another p pump 24v build
  52. another ppumped build thread
  53. Lost some power
  54. Twinned p pump 24v issue numbers low
  55. P-Pumping my 2000 for dependability, economy, peace of mind, and yes, because it is C
  56. Hp with stock HO (245) injectors. 160 pump,
  57. 01 cummins ate the cam sensor
  58. Couple small issues.
  59. Flexible emergency fuel line?
  60. P pump 24v pistons
  61. Dv ?'s
  62. p pump issues
  63. Problems
  64. Choosing a secondary for 1200 hp
  65. Help! Having p pump problems!
  66. Idle trouble
  67. Idle adjustment screw
  68. Tappet cover bolts.....
  69. crazy Carl intake plate
  70. Issues with throttle going up after engine is warm...
  71. Who has "re-bent" their own VP conversion lines?
  72. Is it worth going to a S480?
  73. Crazy Carl's tunnel ram for ppump conversion
  74. Ppump 24v lines with tube intake runner need help!
  75. Tach problem on 99 conversion
  76. oil catch cans
  77. Is this normal? Idle question
  78. Oil, fuel, and fuel return on drivers side of ppump???
  79. White smoke on startup and long crank without tapping pedal
  80. Oil out of crankcase breather after p pump conversion
  81. P-Pump a 6.7
  82. What injectors
  83. Crank signal & tps signal PCM
  84. Starting with throttle, miss around 2800rpms, wont go into gear
  85. Idle and Rev Issues
  86. Am i the only one with bad luck?
  87. Right hand feed and breather issues/questions
  88. Surging Throttle??
  89. Restricted oil fitting
  90. Custom throttle linkage
  91. Which compounds for 01 p24v?
  92. Cam sensor adapter
  93. Compounds and p-pump
  94. Throttle linkage
  95. Ppump 24v Motor Build Suggestions
  96. bad turbo lag, high egt
  97. Hot street ppump 24v
  98. 24v p-pump lines that won't rust?
  99. Project nightmares never ending journey
  100. Big single turbo
  101. Ppump timing question
  102. NV5600 questions
  103. Fummins build
  104. 369 sxe setups
  105. My P24V build
  106. 24 v rods
  107. Weird p7100 idle issue
  108. Rocker arm trouble
  109. Original tach w/ATI damper in a 94??
  110. Sending my pump out
  111. Streetable Compounds for 1000hp on a ppump
  112. bigger compounds
  113. 12 valve intake plate and air horn.
  114. A Few Questions: Cam, Throttle Cable
  115. P-Pump 24v Idle Surge
  116. Piston Suggestions
  117. DDP Comps?
  118. Fuel Shut Off Arm
  119. 87mm Turbine vs. 96mm turbine power potential
  120. P24v timing
  121. Iso p pump
  122. My truck hates me.
  123. Formula for 500 working hp?
  124. trans wiring help!
  125. Is my setup capable of making 600hp?
  126. ECM Relocate with Billet Tappet Cover?
  127. Pump support bracket and throttle return spring
  128. Picking a cam for the first time
  129. Bell Crank and Throttle Levers
  130. Pump identification
  131. Breaking billet cams?
  132. What would you change?
  133. P-pump & electronics
  134. Using adrenaline and tst for monitor
  135. Rpm too high
  136. What delivery valves for twin turbo 24v
  137. Throtle linkage question issues at wot
  138. Towing timing
  139. Water temp sensor
  140. P-Pump 24V Won’t Hardly Start Anymore?
  141. Ppump24v build
  142. p-pump no start-electrical
  143. conversion help
  144. Finally got my pump done
  145. Realistic Setup
  146. Finally doin the swap
  147. F1 Mach 3’s.