View Full Version : Dodge Tech
- Length of 12mm main studs
- What tuner should i use ??
- Ram 3.0L
- And its gonna go here... 4bt Coolant Question
- Gas VS Diesel 2500
- B&M transmission pan for 47re
- A different bypass...
- Anyone know Holset turbos very well?
- Needing a dual disc for 5 speed 12 valve
- Anyone DD a manual VB?
- Best year for cummins 5.9
- Battery cable replacement?
- Steed manifold coatings
- Need help identifying this
- Cummins Barring tool
- Issue with HVAC controls
- 47RH vs 48RE case
- Full manual vb 47re issues
- 1996 dodge dreaded converter locking and unlocking
- Superchips update....
- Mag hytec bolt length?
- 06 block used in 24v
- Cab removal, 1995 extended cab
- 190 pump timing?
- Diesel shops
- Misc questions thread
- New starter, stick with OEM?
- Shorter sway bar links for lowered trucks
- Evoht
- engine/trans running temps...
- Connecting rods
- Major (possibly) electrical issues
- Nv5600 bellhousing
- Main bearing cap alignment dowels
- Cummins or Duramax
- New complete axle's?
- Cursed transmission! 47RE
- 2001 ECM and PCM wiring Harness
- dresser roller with a 6bt cummins
- who builds p pumps
- Dodge Cummins Water Pump Comparison- Tech Info
- Switching away from amsoil
- carrillo wrist pin clearances
- Cowl fasteners
- 47RE Shifting Problem with a Twist
- 12 valve breathers
- what do yall recommend?
- trans shops in Chicago
- New Dodge Recall 2010-2014 affected.
- what chip is reccomended
- 47 RE/RH questions
- Bent Push Rod? Whats next?
- 47RE Shuttles in/out of lockup
- Can I get a good converter...
- Starter Question
- Smarty Jr 67 ME codes for '09
- Fass/fleet guard
- looking for a new truck
- Opinions 12V vs p pumped 24V
- what am I missing?
- Stainless Diesel Spring Gate
- Turbo choices
- Clunk in driveline
- 2146 w/Ohm Reading... Help!!
- Anyone know anything about phoenix friction brake pads?
- Grant Steering Wheels
- How do you stop a 47re pan gasket from leaking
- 47re no 3rd gear
- 05 cummins auto ecm flash
- why did my headgasket fail?
- Is 1st gen dodge cummins bellhousing different from 2nd gen?
- Steed speed wastegate block off
- P-pump 24v lines
- 6.7 intake horn on 5.9?
- Smarty UDC Custom Tune Pro Software!! Interesting!!
- Another Oil question
- curved 40" light bar combo kit ?
- 48re front band adjustment went in very far. Bad sign?
- exhaust manifold help
- Cummins from India.
- 47re overdrive brake stepped backing plate source
- good cummins for tuning
- Turbo help
- 47RE/RH Lube Paths
- Random vibration
- Exhaust manifold flange specs
- Good Machine Shop In DFW Area
- ECM issue?
- Manual transmission rebuilds. Nv4500, nv5600, g56
- Twins Question
- Need a straight answer
- 07-09 dually to single wheel question
- '96 Puking Power Steering Fluid
- Uploading pictures!!!!
- Best place for reman engines
- Manton Rocker Trunions
- New Truck, Is It Worth It?
- Auto meter broken wire terminal
- A518 and 47RH
- Wanted... Old HTT 16cm stainless s300 turbine housing
- Help, 6.7 main bearing question
- Overbuilt 1998 Ram 2500 12 Valve (Build Progress Thread)
- 6.7 stick in a 5.9 hole
- Help with 47re (advanced diognostics)
- Shopping for a common rail, 3rd gen vs 4th gen
- 5.9 Oil cooler on a 6.7 block
- Oil Pan Question and Wtf moment
- Valve Adjustment help - Richmond, KY
- 2WD Overdrive Gear Cluster Stuck In Case...
- Custom Machining Transmission Parts...
- S475 trade for S480
- ATS 12v intake
- Front Driveshaft length
- Questions on 47re and 48re
- Nv4500 for 5 bills ?
- Wastegates
- Holset/Cat compound turbos
- Schwitzer turbo specs ?
- Air Dog dual filters, no seperator
- Ever wonder why...
- Fuel rail pressure stuck at 27,535
- Suncoast 25 spline converter/input
- 12 valve over heating
- Gap in new main seal
- CA Courtesy Letter
- 4 speed rpm drop on shifts
- Full electronic 48re valve body
- Trans cooler questions
- Need help with my Allison in my Cummins
- Bed differences in 2007 and 2010 structures
- Smarty Jr ME Software
- Turbo Upgrade- help? 3rd gen w/ 2nd gen swap/90hp nozz/fass fuel/monster intake&more
- 98 12v 5 speed swap into 01 24v truck
- he351 vs he341
- 6.7 saddle jet plugs ?
- Drilling Sprag
vBulletin® v3.8.7, Copyright ©2000-2024, vBulletin Solutions, Inc.