Competition Diesel.Com -  Bringing The BEST Together

Competition Diesel.Com - Bringing The BEST Together (http://www.competitiondiesel.com/forums/index.php)
-   Dodge Tech (http://www.competitiondiesel.com/forums/forumdisplay.php?f=84)
-   -   2WD Overdrive Gear Cluster Stuck In Case... (http://www.competitiondiesel.com/forums/showthread.php?t=197986)

michael.kitko 10-10-2017 12:02 PM

2WD Overdrive Gear Cluster Stuck In Case...
 
I have finally gotten over the majority of the deck build, so now I am getting some time to do some work on my fummins project.

Anyways, yesterday I went to disassemble the rear 2wd overdrive section of the 46rh. I took out the speedometer housing, removed the output yoke, took the small ring out, removed the clutches, took the wave ring out, took the other snap ring out, then I set it up on a block of wood, went to unclip the gear retaining snap ring and the gear train literally moved about a 1/10 of an inch. I just can't get the gear train free from the housing. I even pushed it back up inside a few times and expanded the ring again to see what all was moving. I even did small taps with a rubber mallet and tried pushing really hard. It just won't move. I don't know if it is related, but there seems to be a ticking noise when I rotate the gear assembly.

Now, three days ago, I took my 4wd overdrive housing apart on the 47rh and did the exact same thing, minus the speedo of course, and when I set it up right and then expanded the snap ring, the gear train came right on out with a nice thud.

Am I missing something on the 2wd section or is there something broken and stuck?

My manual is an ATSG. I did ask this same question on another forum and figured why not ask here as well.https://uploads.tapatalk-cdn.com/201...4a997672a1.jpghttps://uploads.tapatalk-cdn.com/201...bd557f09f6.jpghttps://uploads.tapatalk-cdn.com/201...1adf4f8cf9.jpg

Sent from my S60 using Tapatalk

michael.kitko 10-11-2017 05:58 PM

Got it out and from the sounds of it, I saved loads of money. For anyone in the future who may have this issue, it appears oil flow to the governor bearing and seals caused it to gall.

Here's what I did:
1. I cut the c-clip through the speedometer housing and removed it.
2. Drilled the side of the case and filed it out to get at the governor shaft and e-clips.
3. Pulled the e-clips and then the shaft out.
4. Spread the spring clip that holds the rear bearing in, the assembly dropped out.
5. Pulled the spring clip and pulled out the oil tubes.
6. Filled out the hole I made, tapped it, and built a cover.https://uploads.tapatalk-cdn.com/201...727baaef99.jpghttps://uploads.tapatalk-cdn.com/201...797e143871.jpghttps://uploads.tapatalk-cdn.com/201...9313913b2f.jpghttps://uploads.tapatalk-cdn.com/201...797b3160b1.jpghttps://uploads.tapatalk-cdn.com/201...e98c8624ae.jpghttps://uploads.tapatalk-cdn.com/201...1a3d94eaf4.jpghttps://uploads.tapatalk-cdn.com/201...2f98541703.jpg

Sent from my S60 using Tapatalk

turbo2387 10-11-2017 07:52 PM

Its amazing what people can to with a little want too. Nice work.

michael.kitko 10-12-2017 10:32 PM

Quote:

Originally Posted by turbo2387 (Post 2639028)
Its amazing what people can to with a little want too. Nice work.

Thank you. In all honesty, I just hope this helps someone in the future, when a shop tells them it's stuck and it'll be like $400 to repair.

Sent from my S60 using Tapatalk


All times are GMT -5. The time now is 02:08 AM.

Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com