Competition Diesel.Com - Bringing The BEST Together
Page 3 of 6 12 3 45 Last »
Show 40 post(s) from this thread on one page

Competition Diesel.Com - Bringing The BEST Together (http://www.competitiondiesel.com/forums/index.php)
-   Dodge Competition and Performance (http://www.competitiondiesel.com/forums/forumdisplay.php?f=31)
-   -   Fuel fittings/ thread size database (http://www.competitiondiesel.com/forums/showthread.php?t=85373)

bsmith 05-26-2011 10:38 PM
Quote:
Originally Posted by getblown5.9 (Post 1412143)
Anyone know what the thread pitch on banjo bolt for a 12v injector return line is? Buddy put a fass on his 12v and removed the stock filter etc. We need to make a t-fitting where the injector return can thread in the top and the injection pump can then tie back into it and then back to the tank.
I'm pretty sure its m14x1.5

CREED1 06-13-2011 07:28 PM
Anyone know were to find M14x1.5 to -6an banjo fitting looking for one with hose ends etc I can find it in 9/16 but not sure if it will seal if I go that route anyone know if it will?

RJM06590 06-13-2011 07:54 PM
Hose End - Fragola Aluminum Metric Adapter

Mighty Goat 06-13-2011 08:40 PM
14mm To -6 AN Banjo Fitting Kit - Fitting, Bolt, Gaskets [G-053] - $29.90 : Himni Racing, Turbocharger, Turbo, Garrett, Turbo Kit, GReddy, Mazda RX-7, HKS, Apexi, TiAL, TurboXS, TurboSmart, Flange, Turbonetics, Exhaust, Intercooler, ACT, Intake

Link to what you want there Creed. FYI Garrett GT35R and below use a 14m x 1.5 for coolant, GT37R's use 16m x 1.5, GT40R and up use 18m x 1.5.

And other fittings like it.

Turbo & Fuel Fittings : Himni Racing, Turbocharger, Turbo, Garrett, Turbo Kit, GReddy, Mazda RX-7, HKS, Apexi, TiAL, TurboXS, TurboSmart, Flange, Turbonetics, Exhaust, Intercooler, ACT, Intake

mpracehemi 06-13-2011 09:29 PM
Quote:
Originally Posted by CREED1 (Post 1479980)
Anyone know were to find M14x1.5 to -6an banjo fitting looking for one with hose ends etc I can find it in 9/16 but not sure if it will seal if I go that route anyone know if it will?
Try summit or jegs also...

CREED1 06-13-2011 11:10 PM
1 Attachment(s)
Here is the 12mmx1.5 banjo that I need and kinda want to find a 14mmx1.5 similar in type so I wont have to run a banjo 14mx1.5 with -6 end and then a straight -6 fitting basicly eliminat the need for the straight fitting on like the 12mmx1.5 -6 below uses so I can hook straight to braided hose.
Attachment 30616

CREED1 06-13-2011 11:13 PM
2 Attachment(s)
By running the above ^ style I would eliminate having to run the two below together basicly eliminate one connection.

Attachment 30617

Attachment 30618

Mighty Goat 06-13-2011 11:35 PM
I did my 03 in braided stainless. I didn't even know what you're wanting existed. That said, I'd contact whomever makes the part above.

RJM06590 06-14-2011 10:23 AM
I found one before, but can't remember the website. I think I just kept searching google under various names.

cumins01 06-14-2011 10:33 AM
So is the one for back of the head for a 24v a m12 1.5? I need one just don't want to get the wrong one.

Mighty Goat 06-14-2011 11:32 AM
^ yes. It's m12 x 1.5

connermcpherson 06-14-2011 04:46 PM
Quote:
Originally Posted by CREED1 (Post 1480266)
By running the above ^ style I would eliminate having to run the two below together basicly eliminate one connection.

Attachment 30617

Attachment 30618
Or u can eliminate both of them and regulate the return.....

CREED1 06-14-2011 05:50 PM
Quote:
Originally Posted by connermcpherson (Post 1480773)
Or u can eliminate both of them and regulate the return.....
Ya just not much room between the head and the pump to get a m14x1.5 -8 and a -8 90* in there but im sure it can be done im still searching for the m14x1.5 -6 banjo worse case ill use the two piece deal i posted earlier.

bsmith 06-14-2011 07:28 PM
Quote:
Originally Posted by CREED1 (Post 1480816)
Ya just not much room between the head and the pump to get a m14x1.5 -8 and a -8 90* in there but im sure it can be done im still searching for the m14x1.5 -6 banjo worse case ill use the two piece deal i posted earlier.
Did you check with vulcanpreformance.com? I think they have that fitting.

CREED1 06-14-2011 08:07 PM
Quote:
Originally Posted by bsmith (Post 1480910)
Did you check with vulcanpreformance.com? I think they have that fitting.
Yep but there's is a pushloc style im looking for one that is -6an for stainless hose

bsmith 06-14-2011 08:20 PM
Quote:
Originally Posted by CREED1 (Post 1480944)
Yep but there's is a pushloc style im looking for one that is -6an for stainless hose
Try anplumbing.com

fordassassin 06-15-2011 01:07 AM
What fitting goes in the 48re to the cooler? Looking to do braided or hydraulic lines from the transmission to coolers up front and then back to transmission.

cumins01 06-17-2011 11:16 AM
Looking for fitting size on top of engine oil cooler that the turbo oil feed line goes on. 24V if it makes a difference. Mine stripped out and wanting to go next size up. Prefer a standard thread to -06 but metric thread to -06 will work

bsmith 06-17-2011 01:35 PM
Quote:
Originally Posted by roachie (Post 1271067)
Oil cooler pressure fittings (to the turbos)

1/8 NPT and M12x11.5 straight metric oring.
Quote:
Originally Posted by cumins01 (Post 1483381)
Looking for fitting size on top of engine oil cooler that the turbo oil feed line goes on. 24V if it makes a difference. Mine stripped out and wanting to go next size up. Prefer a standard thread to -06 but metric thread to -06 will work


See above^

cumins01 06-17-2011 02:11 PM
Sorry did not see that one. Over looked it


All times are GMT -5. The time now is 04:14 AM.
Page 3 of 6 12 3 45 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com