GM 9.5 IFS durability?

Inbred Inline

Inbred Inline

Bastard child builder
Has anyone been having any issues with the GM IFS center unit holding together in limited pro? Have seen a couple broken D60s which has me wondering. Probably going to end up putting RCVs in my truck just wondering if I should do a 11.5 front at the same time and be done with it.
 
At what power is that class?

The r&p are pretty strong, the factory slide collar is junk.
 
I've seen the shafts break before the center section breaks but then you always have to replace both shafts. Occasionally, I've seen the center section have issues if it's a violent driveline breakage somewhere else.

I'd stay away from the 11.5. Its a good quality axle but it's a pain to set up compared to a F106 front. They cost about the same and I would venture to guess you could maybe get a F106 for cheaper.
 
takedown95 said:
I've seen the shafts break before the center section breaks but then you always have to replace both shafts. Occasionally, I've seen the center section have issues if it's a violent driveline breakage somewhere else.



I'd stay away from the 11.5. Its a good quality axle but it's a pain to set up compared to a F106 front. They cost about the same and I would venture to guess you could maybe get a F106 for cheaper.
Click to expand...



Are you talking about a IFS 106 center or a complete fds 75 straight axle assembly?

I haven't found a price on the 11.5 yet, I might get around to that tomorrow.


Sent from my iPhone using Tapatalk
 
I was talking about a F106 straight axle in terms of cost comparison to a 11.5 IFS.

I would still take a straight over IFS for a F106. You may not break the center section but those shafts seem like they break often and from what I understand if one breaks you have replace both.

If you are looking for IFS 11.5 or IFS/Straight F106 I think Proformance pros carries all three (Including the straight F106). Although you may not buy one from them at least you can get a cost comparison in relative form.
 
Last edited:
Inbred Inline said:
Has anyone been having any issues with the GM IFS center unit holding together in limited pro? Have seen a couple broken D60s which has me wondering. Probably going to end up putting RCVs in my truck just wondering if I should do a 11.5 front at the same time and be done with it.
Click to expand...

So far we have not had any issues with the IFS on our truck (knock on wood). In 4 years have we have never broken a stock coupler or anything on the track. Replaced one right side shaft that had a slight twist in it when we took it apart to look things over one time. We do check the CV's for backlash after every pass and replace them as soon as they start to get sloppy. We built a mechanical setup to engage the coupler so you know for certain the coupler is fully engaged every pass. It is my belief that most all issues with breakage on these come from the slide coupler not being fully engaged to start a run or from shock loading that starts elsewhere in the driveline.
 
cfunk said:
So far we have not had any issues with the IFS on our truck (knock on wood). In 4 years have we have never broken a stock coupler or anything on the track. Replaced one right side shaft that had a slight twist in it when we took it apart to look things over one time. We do check the CV's for backlash after every pass and replace them as soon as they start to get sloppy. We built a mechanical setup to engage the coupler so you know for certain the coupler is fully engaged every pass. It is my belief that most all issues with breakage on these come from the slide coupler not being fully engaged to start a run or from shock loading that starts elsewhere in the driveline.
Click to expand...



I have never broken a stock slider however I have twisted off a couple short shafts it goes over. I have the posilock cable on mine and being a 90s Chevy front end it has a independent indicator switch that works very well for telling when it's in gear.


Sent from my iPhone using Tapatalk
 
I have ran a GM 9.25 ifs for a few years and have only broke stock cv shafts when my main shaft in the transfer case broke sending all power to the front wheels. I do have the Fleece axle shafts, Elocker and this year upgraded to the RCV cv shafts.
 
You must log in or register to reply here.
Back
Top