F250/Cummins Swap

Yes, by what looks to be one rib

Sent from my XT1575 using Tapatalk
 
Any ideas on how to correct the misalignment using this compressor?

Sent from my XT1575 using Tapatalk
 
Engine is home. Reworking a 6.7 harness to work with the CM849.
2aa2eaf3557c7d96f71a378b86491ec2.jpg
b206ac016abc0ced7764c2c1fd0ca6f6.jpg


Sent from my XT1575 using Tapatalk
 
Well..... I decided to go ahead and coat the turbine housing.
I also had to take a slight detour on the transmission. I went to replace the pump housing seals. Killed a friction, then I went over to Kingspeed to get help setting up the clutch packs and discovered that direct was toast. So ended up building those two clutches. I also went ahead and jumped on a DPC converter. Got the trans closed up today.
d23f95609df9f05fca869cc79ad7a6c8.jpg
98852fea21c623446e1c08b992f78f10.jpg
9932fbbbd7684a0d7c1ca3e358cca8b4.jpg
f31792fd8f8d988a16a1033cf26b9425.jpg
bb24d344555c7bf1c51fcf4e4d47c71c.jpg
59ca137c9b1a24dc508d77a558db874e.jpg
aeb80bcda83becbed42106aa806dcece.jpg


Sent from my XT1575 using Tapatalk
 
Challenge of the day. I need this sensor on the hot side of the thermostat.

I'm going to look at the temp sensor from a Powerstroke, but the plug is different.

The preferred mount location is to replace one of these plugs with a sensor that is Ford ecm/cluster compatible

f156b30abecb8f4d7843b5e2ed4c7e42.jpg


Sent from my XT1575 using Tapatalk
 
What's the preferred location to connect to when prelubing a 6.7? I want to do this for initial startup, and also for a vehicle installed preluber I've been thinking about building.

Sent from my XT1575 using Tapatalk
 
I pre oil a 5.9 at the oil filter housing thru the turbo oil fitting then oil turbo separate. With a pneumatic pressure type Oiler. Should be same on 6.7.
 
That's what the others I've asked have said also.

Sent from my XT1575 using Tapatalk
 
Back at it. I plan to crate run the engine this weekend. I have to sort out some version of a fuel system. Tentative plans for transplant next weekend.

Wiring: miscommunication led to stripping the loom from the original harness and rewiring a good deal of what I had done, but I also had the chance to improve on some things.
Carbon Fiber Tech Flex.

I bought a power steering pump, and less than 12 hours later a co-worker hands me one for free. The picture is me pulling the Ford pulley partially off to clear the dodge pump mount bracket.

I don't have pictures, but I have the belt run, I got an AC compressor for an 06 and it will not bolt to my 03-05 ACC bracket. I have to sweet talk the parts house on that one.

Lots to do still.

Glamour shot from work.



Sent from my XT1575 using Tapatalk
aaaa444cd5720746490602b8ab9fc03e.jpg
6735107325272c2b6eadf71051096cbf.jpg
61858ff1b3e45455d345e34c0dcd3ab9.jpg
7a11e770e1ef977615542fa52ffd34dd.jpg
d11ba52023dcaa740e1cdeb25d156474.jpg
208794eddba03a5e230edf024fcfc65f.jpg
7d957b35754de786deb67465d867f91d.jpg
09ae7dba6d9aa480d345839d6d0e391f.jpg
 
Last edited:
Thank you.

That harness looks silly where it is. I had it pulled out of place to pin the ECM connector. I will get pics of its final resting place.



Sent from my XT1575 using Tapatalk
 
Anyone know the official title for the xip tie anchors that go in threaded holes? They work like Christmas tree fender fasteners.

Sent from my XT1575 using Tapatalk
 
Tapatalk is being stupid.

Fir tree zip tie anchors

Got my AC comp, PS pump mounted, belt on.

Caitlyn is mounted.

The beta anteater harness was eleventy billion feet long. I cut it down and added a duetch connector at the bell housing.

Anteater is mounted to the block with uhmw polymer to air gap it from the block (so Joe farmer doesn't send me hate mail)

Downpipe. Tight fit with the dipstick on the trans. Stainless diesel piece. It angles down and out (out of square on two planes).
I expect to have to mod it, so it's not that big a deal.

The jamo exhaust is 4" for the first 3 feet, so I'm hoping to knock that out with minimal effort.

I disappeared the harness I had for my apps, and I'm not engineering a 2 micron fuel system just to run ~15 minutes in my garage.
fe898556fac4f33f2ba11439ee91f6ec.jpg
b2df8e5fbb4fd24849779171fb48b147.jpg
9afbf67575598397385c50155833e5d6.jpg
48c9ada4fa467ebe80854453e327bf32.jpg
42217564d6aa1c38ff02625ae1a0c1ab.jpg


Sent from my XT1575 using Tapatalk
 
Last edited:
never seen fir tree zip tie anchors. They'll clean up the bay nicely.
 
They suck to remove from a threaded hole. I should have some tomorrow night.

Sent from my XT1575 using Tapatalk
 
Since I'm doing my fummins swap, I've been toying with how to enable cruise control. It looks like C2-38 is able to call a specific RPM/map.

Is it possible to have it assume whatever RPM the engine is currently operating at?

Using EFI?

Sent from my XT1575 using Tapatalk
 
Back
Top