Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Tech- General Diesel > Import Diesel
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Import Diesel VW TDI, Mercedes, and other Import Diesel Discussion can be found here.

Closed Thread
 
Thread Tools
Old 09-26-2012, 08:36 AM   #1
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Injection Pump fuel adjustment for Mercedes Diesels, Bosch M and RW governors

Disclaimer!
All information presented herein is purely for informational purposes only, I and MercedesForum assume no liability for your or anyone else's actions. All procedures and adjustments in this guide are to be performed AT YOUR OWN RISK. The pump can only be properly calibrated by a Diesel injection specialist on an injection pump test bench, this is not intended as a DIY at home pump calibration guide. Getting your engine into good running condition and installing an exhaust temperature gauge (pyrometer) is STRONGLY recommended before you contemplate touching any injection pump internals. If you believe any of the following information to be incorrect please make a post or contact me through the forum PM system and it will be corrected asap.

Pyrometer, aka EGT gauge
If you skip installing a pyrometer you risk major damage to the engine and turbo from high combustion heat.
Extended WOT of more than 10-20 seconds can create combustion temperatures high enough to damage the engine. This damage is not instant, its cumulative. The longer you run hot the more damage excessive temperatures will do and it won't be obvious there is a problem until its too late. 1250*F (675*C) is a safe limit for continuous output, 1400*F (815*C) is acceptable for short intervals (under 5 seconds).


Boost pressure
First off, more is not always better!

The maximum useful boost pressure is determined by four factors:
1: How much fuel you're injecting
2: If you cool the charge air; Intercooler, water injection, etc
3: Altitude
4: Pre-turbo exhaust pressure

A pre-turbo exhaust manifold pressure (EMP) gauge is very recommended to help determine the ideal boost pressure. The "no visible exhaust smoke" method works, but its like trying to assemble a jigsaw puzzle without the box picture.
An EMP gauge can be built by installing a brass ferrule fitting in the manifold before the turbo and using 2' of 1/16" copper tube (to cool the exhaust) with a standard boost gauge. The EMP gauge should read 2x that of your boost gauge for adequate measuring range.
Click the image to open in full size.

When boost pressure is excessive, drive pressure will be higher than 2:1 to boost pressure. This is caused by a lack of fuel to spin the turbo fast enough. Drive pressure higher than 2:1 has two major effects, it drastically increases exhaust temperature and increases engine pumping losses. Both increase stress on the engine and reduce horsepower.

The perfect ratio is 1:1 but 1.5:1 is also very good. You have found your ideal boost pressure when your turbo is working in this range and there is no visible black smoke from the exhaust.

Some examples of boost pressures I recommend. These are not guesses. They are based both on airflow calculations and real-world trial and error.
Stock engine: 11psi
Stock engine with an intercooler: 8psi
Rack limiter removed without an intercooler: 17psi
Rack limiter removed with an intercooler: 12psi
Note: These boost pressures are at sea-level (14.7psi-absolute). If you live above 4000ft elevation you will need more boost to make up for the lower atmospheric pressure (For example, Denver's barometric pressure is 12.1psi).
Here is an airflow calculator to help you determine the boost you need (its already programmed for a factory-stock OM617a): http://www.not2fast.com/turbo/glossa...torDutyCycle=0

Altering the air filter and exhaust systems do not provide any benefits in power or economy.
The stock intake is already a true cold air intake and the filter flows efficiently to 400cfm.
The stock mufflers are a straight-through, unbaffled, design and the diameter is already large even compared to modern cars.
Click the image to open in full size.Click the image to open in full size.

Installing an aftermarket "cold" air intake, installing a larger diameter exhaust and/or removing the mufflers will produce a 0hp change in power. The only change they will produce is noise.


Injection pump adjustment
NOTE: After adjustment, refill the pump with fresh oil (about 1/2 quart). On the MW, the fill port is a plug on the top left side of the governor housing (The ALDA points its direction in the picture below). On the M, remove the shutoff actuator.

MW-Pump
Click the image to open in full size.

No idle compensation is required unless noted.

External Idle Screw- Controls the fine idle speed.
*Set the engine between 700-800rpm.

ALDA- Limits fuel at low boost pressure to control black smoke.
*Loosen the 10mm locknut and adjust the screw CCW in 1/4 turn increments to increase low boost fuel until you see black smoke when the accelerator is floored from a standstill. This adjustment will NOT increase your maximum horsepower.

Throttle stop- Prevents the external linkage from forcing the internal linkage past set point.
*Do not touch but make sure your external linkage is contacting the stop at WOT.
**This adjustment will NOT increase your maximum power and can possibly cause internal linkage binding.

High Idle- Limits maximum engine RPM.
*This can effect the governing of idle RPM and idle quality.
**This should only be adjusted if your engine is in top-notch condition.
***Increasing maximum RPM comes with a serious risk of throwing a connecting rod and/or floating the valves resulting in catastrophic engine damage.

Full Load- Sets the maximum rack travel while the engine is running.
*19mm and 9mm locknuts must be loosened and the 13mm nut turned CW to increase maximum fuel quantity.
**The rack limiter lever can be completely removed from the pump for maximum power. See below for this procedure. Anyone that tells you NOT to remove the limiter is inexperienced and should be completely ignored. Removing the rack limiter is the ONLY way to get maximum power from your engine. Leaving the limiter in place, by definition, will LIMIT your maximum power.

Idle Regulation Bumper Spring- Adds idle unloading spring force against the flyweights.
*Should not be adjusted.

Coarse Idle RPM Screw- Sets the idle speed in combination with the outer fine adjustment.
*Should not be adjusted except in conjunction with torque control capsule adjustment.
10mm lock nut.
Start Quantity Cutout- Allows full fuel for start but not run.
*Also affects other internal functions. Do not touch.

Torque Control Capsule- (Do not adjust) Reduces rack travel with increased RPM.
*Reduces smoke at higher RPMs due to the engines lower volumetric efficiency at higher RPMs.
*Loosen 21mm lock ring and turn 14mm capsule CW to increase. Back out the coarse idle RPM screw by the same amount as you turned the capsule.
**A pyrometer is an absolute must if you are going to adjust this. Take it easy and only go 1/4 turn each time.
***Caution: Adjusting the capsule is not suggested. Adjusting it will result in the engine becoming slow to return to idle and excessive EGTs at high RPMs.
Click the image to open in full size.

Full Load Limiter Removal Procedure
An exhaust temperature gauge (pyrometer) is necessary for reliable long-term operation of the engine after this modification. Do not exceed 1250°F in continuous operation or 1400°F in short bursts (under 5 seconds). Do not use any kind of sealer on any of the gaskets.

Anyone that tells you NOT to remove the limiter is inexperienced and reckless. Removing the rack limiter is the ONLY way to get maximum power from your engine. Leaving the limiter in place, by definition, will LIMIT your maximum power by LIMITING how far the fuel rack can move towards maximum fuel. Adjusting the torque control alone will only result ing high EGTs above 3000rpm, not any more usable power.

1: Remove the oil-filter housing. This is optional, with a long screwdriver its very possible to adjust everything with the housing in place.
2: Remove the pump back plate including shut off actuator and rack damper.
3: Disconnect the vacuum device linkage and tubes. Remove the top lid screws, turn the top lid (or remove both the ALDA and top plate for best access).
4: Remove the limiter's screws and nuts.
Click the image to open in full size.
5: Push the limiter from the adjusting screw into the inside of the pump.
6: The hardest part is "digging" the limiter out of the bottom of the pump. A pen magnet is strongly suggested for this step. It can only exit through the thin slot on the top of the pump. You have two options- You can turn (rotate) the parts around inside the pump or you can punch out the guide pin the limiter used to slide on. The pin is no longer needed.

7: Once the limiter is out replace everything back in reverse order minus the limiter. Remember to use a new oil filter housing gasket and get the filter housing and block mating surfaces surgically clean. Be careful not to drop any gasket leftovers into an oil channel. If you get an oscillating idle this is a good place to replace the Rack Damper bolt with upgrade unit (upgraded one is gold anodized, the old silver in color) in the back plate of IP.

Note: No governor adjustments are necessary. The rack limiter only affects the maximum available throttle/fuel when the engine is running, it has no effect on any other governor functions.

When you are done, you should have 5 or 6 parts left over (depending on the removal method you chose). DO NOT DISCARD THESE PARTS in case you decide to revert the operation at a later date.
Click the image to open in full size.




M-Pump
Click the image to open in full size.

The procedure should be the same for all OM601/2/3, pre-1996 OM604/5/6 and European OM616/7 engines, but the throttle linkage setups will vary between models.

Click the image to open in full size.

Click the image to open in full size.
17: Torque Control Capsule- Reduces rack travel with increased RPM.
23, 24: High Idle- Limits maximum engine RPM.
25: Full Load- Sets the maximum rack travel while the engine is running.
28: Coarse Idle RPM Screw- Sets the idle speed in combination with the outer fine adjustment.
29: External Idle Screw- Controls the fine idle speed.
50: Related to low idle adjustment (28)

Click the image to open in full size.Click the image to open in full size.
Left- OM61x european models
Middle- OM60x non-turbo models
Right- OM60x turbo models


1: Remove anything blocking access of the rear of the pump. On the 86/87 603, this means pulling the windshield washer reservoir, all throttle linkages, the bowden cable and the cruise control actuator. The oil filter housing does not need to be removed on the OM60x or OM61x engines and the intake manifold can remain in place on OM60x engines.

2: Remove the ELR (round red device at the top-rear of the IP). The Torx screws may be tight due to the factory locking compound on the threads. This does not apply to OM617 engines.
[attachment=4086]

3: Unscrew the rear governor plate (6 screws). Early pumps have flat head screws, late pumps have Torx screws. When you pry of the plate, a fair amount of engine oil will spill out. Have rags handy to catch the mess.

4: Now you should have full access to the governor of the pump. To increase the full-load fuel quantity, loosen the jam nut, and turn screw 2f (bottom left) out (CCW). Make careful note of the position of the slot, before & after adjustment. Try 1.5 turns total for the first adjustment, or go in half-turn increments if you don't want to max it out. For the OM617, this will bring power near that of the stock MW-Pump.

NOTE: Poor idle quality (1000rpm+ unloaded, 500rpm in gear) is known above 1.75 turns for the OM60x and above 5 turns on the OM61x. 2 turns CCW of the nut 2K (idling auxiliary spring) will restore the idle speeds to normal.

5: Whatever number of turns you made to full-load screw 2f, make the IDENTICAL adjustment to the idle stop screw, 2b (top/right). If you turn 2f out 1.5 turns CCW, then also turn 2b out 1.5 turns CCW. This decreases the idle setting but it also moves the external throttle lever. After the idle adjustment, make sure the lever is not touching the pump body. If screw 2b is backed out too much, it can touch the intermediate plate behind the ELR. Check the spec per the FSM procedure if you must change any shims for clearance.

NOTE: Make sure your new settings do not change when you tighten the jam nuts on both 2f and 2b. Make sure the nuts are snug, but don't over-tighten them... if you break something, you could end up pulling the pump to repair or replace.

6: If possible, use a new gasket for the rear cover, and a new O-ring for the ELR. They are available from Mercedes dealers at a reasonable price. Clean and dry the sealing surfaces, re-install the cover and ELR.

7: Because you turned screw 2b, which moved the external throttle lever towards the rear of the engine, you now must adjust all three throttle linkages. Lubricate the ball/socket joints with ATF or wheel bearing grease before re-attaching them. Due to the number of vehicle models this guide crosses, linkage adjustment is not detailed in this post. Use the procedure in the factory service manuals to adjust your throttle linkages, just remember that the rod lengths specified in the FSM no longer apply after you internally adjust the injection pump.

8: Re-connect the transmission Bowden cable. Slacken to lower shift RPM, tighten to raise. Make sure the cable travel is not limiting linkage movement, you may need to bend the bracket slightly.

9: Press the pedal to the floor and inspect the lever at the back side of the pump, it should go through the entire range of motion from the idle stop to the WOT stop. You can have a helper sit in the car or use a heavy object placed on the pedal. Be sure to remove it before starting the engine!

10: Reassemble all the items you removed to gain access to the pump.
OM60x: Leave the ELR wire off and start the engine. The idle should be ~500rpm. Re-connect the ELR wires and the idle should jump to ~650rpm if you have the trim plug set to #4.
OM61x: Use the external adjustment screw 3 to fine-tune the idle speed. CW decreases idle, CCW increases idle.

11: Test drive! With the engine fully warmed to 80*c during the daytime (not night), watch for black smoke. You will probably notice smoke when you mash the pedal from a stop.
OM60x: If smoke is visible until boost builds, lean out the ALDA setting by adjusting the screw CW 1/4 turn at a time or removing the shim, installing a thinner shim until the smoke is not clearly visible once the vehicle starts moving.
OM61x: These engines do not have an ALDA on the M-Pump. You will have to live with some smoke, adapt your driving habits to prevent it (with good throttle manipulation) or fabricate an ALDA using a 5-8psi wastegate actuator attached to the STOP lever.

No smoke should be visible at WOT, after the turbo has spooled up, if you have the boost set at 14psi.

12: Watch your exhaust temperatures! Extended WOT of more than 10-20 seconds can create combustion temperatures high enough to damage the engine. This damage is not instant, its cumulative. The longer you run hot the more damage excessive temperatures will do and it won't be obvious there is a problem until its too late. 1250*F (675*C) is a safe limit for continuous output, 1500*F (815*C) for very short intervals (under 5 seconds).

Most of the increased fuel feed from either of these pumps can be noticed between 2000 and 4000 rpm's, after that the high idle (maximum RPM) setting automatically starts to reduce fuel. Boost pressures above 14psi should not be needed although YMMV as to the exact boost PSI needed.

Maximum RPM
Loosen the 29(?)mm lock nut of 2m and turn the 10mm Allen screw CW.
One half turn = 150rpm.

Torque Capsule
Loosen the 22mm lock nut of 2e and turn the 12mm 2-prong capsule CW.
This adjustment will raise the RPM when the governor starts to pull back fuel (due to the engine's reduced volumetric efficiency).
Adjustment is not recommended for the first time modifications. It will cause a slow return to idle (no deceleration fuel cutoff).


keywords: STD superturbo superturbodiesel turbodiesel w123 w126 w116 300D 300CD 300SD 300TD OM616 OM617 OM602 OM603 OM605 OM606 CDI IP injection MW-pump M-Pump power diesel
 
Old 09-27-2012, 01:18 AM   #2
Smoken Gun
 
Smoken Gun's Avatar

Name: Smoken Gun
Title: Diaboli parum adiutor.
Status: Not Here
Join Date: Nov 2010
Location: Michigan
Member`s Gallery
Posts: 3,200
Anyone else think this is "300D"'s new acccount? Sure sounds like him (not just in this thread).
 
Old 09-27-2012, 10:05 AM   #3
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Anyone ask your opinion about anything other the topic of this thread?

If you have nothing to say about the thread topic please on out of here. Thanks.

Last edited by Tormentor; 09-27-2012 at 10:07 AM.
 
Old 09-27-2012, 10:43 AM   #4
Joesixpack
 
Joesixpack's Avatar

Name: Joesixpack
Title: Pull'n it.
Status: Not Here
Join Date: Apr 2008
Member`s Gallery
Posts: 4,118
Quote:
Originally Posted by Smoken Gun View Post
Anyone else think this is "300D"'s new acccount? Sure sounds like him (not just in this thread).
RIGHT!.... Oh and I need the full sized photo in your avatar.
__________________
Basically stock if I would have built it at the factory.....
 
Old 09-27-2012, 12:23 PM   #5
oldestof11
 
oldestof11's Avatar

Name: oldestof11
Title: Drag racer
Status: Not Here
Join Date: Jul 2007
Location: Dixon, IL
Member`s Gallery
Posts: 9,084
Quote:
Originally Posted by Smoken Gun View Post
Anyone else think this is "300D"'s new acccount? Sure sounds like him (not just in this thread).
After doing some digging, I believe you.
__________________
Jon
Click the image to open in full size.
 
Old 09-27-2012, 12:44 PM   #6
12vriviera
 
12vriviera's Avatar

Name: 12vriviera
Title: That Guy with that car
Status: Not Here
Join Date: Mar 2009
Location: north texas
Member`s Gallery
Posts: 6,846
Quote:
Originally Posted by Smoken Gun View Post
Anyone else think this is "300D"'s new acccount? Sure sounds like him (not just in this thread).
Why u ask? Lots of "this is how to do it" without any explanation? (not this thread)
__________________
Brandon Carr.
Owner of the 24V RIV
Competition Diesel.Com - Bringing The BEST Together
I am a pushover
https://www.facebook.com/#!/24VRIVIERA
 
Old 09-27-2012, 12:53 PM   #7
oldestof11
 
oldestof11's Avatar

Name: oldestof11
Title: Drag racer
Status: Not Here
Join Date: Jul 2007
Location: Dixon, IL
Member`s Gallery
Posts: 9,084
I saw that Riv.
__________________
Jon
Click the image to open in full size.
 
Old 09-27-2012, 01:07 PM   #8
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Quote:
Originally Posted by 24vriviera View Post
Lots of "this is how to do it" without any explanation?
I'm sorry. I didn't know you know nothing about engines! Next time I'll give you step-by-step instructions and hold your hand every step of the way.
 
Old 09-27-2012, 01:20 PM   #9
12vriviera
 
12vriviera's Avatar

Name: 12vriviera
Title: That Guy with that car
Status: Not Here
Join Date: Mar 2009
Location: north texas
Member`s Gallery
Posts: 6,846
did you read the part of that post that was in parentheses?
i am talking about every other post you make.
you must be college educated, all that knowledge you try to force down other peoples throats and cant tell us why.
or are you a corporate ass sucker? trying to make your name known and pissing on everyone to get there?
__________________
Brandon Carr.
Owner of the 24V RIV
Competition Diesel.Com - Bringing The BEST Together
I am a pushover
https://www.facebook.com/#!/24VRIVIERA
 
Old 09-27-2012, 01:26 PM   #10
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Quote:
Originally Posted by 24vriviera View Post
you must be college educated, all that knowledge you try to force down other peoples throats and cant tell us why.
Again, I'm sorry for assuming the people here are smart. I didn't realize they were all numbskulls like you. Thanks for pointing it out.
 
Old 09-27-2012, 01:39 PM   #11
12vriviera
 
12vriviera's Avatar

Name: 12vriviera
Title: That Guy with that car
Status: Not Here
Join Date: Mar 2009
Location: north texas
Member`s Gallery
Posts: 6,846
you are welcome. mr 300d
__________________
Brandon Carr.
Owner of the 24V RIV
Competition Diesel.Com - Bringing The BEST Together
I am a pushover
https://www.facebook.com/#!/24VRIVIERA
 
Old 09-27-2012, 01:58 PM   #12
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Quote:
Originally Posted by 24vriviera View Post
blah blah blah
Welcome to my ignore list.

FYI, the correct username is ForcedInduction. Your mistake is understandable and forgiven, its just another major detail you have completely missed.

Last edited by Tormentor; 09-27-2012 at 02:01 PM.
 
Old 09-27-2012, 02:00 PM   #13
12vriviera
 
12vriviera's Avatar

Name: 12vriviera
Title: That Guy with that car
Status: Not Here
Join Date: Mar 2009
Location: north texas
Member`s Gallery
Posts: 6,846
__________________
Brandon Carr.
Owner of the 24V RIV
Competition Diesel.Com - Bringing The BEST Together
I am a pushover
https://www.facebook.com/#!/24VRIVIERA
 
Old 09-28-2012, 01:47 AM   #14
Smoken Gun
 
Smoken Gun's Avatar

Name: Smoken Gun
Title: Diaboli parum adiutor.
Status: Not Here
Join Date: Nov 2010
Location: Michigan
Member`s Gallery
Posts: 3,200
Quote:
Originally Posted by Tormentor View Post
Anyone ask your opinion about anything other the topic of this thread?

If you have nothing to say about the thread topic please on out of here. Thanks.
Nope, but it is a free country, for the time being, so I will post if I damn well feel like it. If you don't like it, well to fukking bad.

Quote:
Originally Posted by Joesixpack View Post
RIGHT!.... Oh and I need the full sized photo in your avatar.
It was obvious from the get go.

Ask and you shall receive: Click the image to open in full size.

http://thechive.files.wordpress.com/...he-gap-291.jpg

Quote:
Originally Posted by 24vriviera View Post
Why u ask? Lots of "this is how to do it" without any explanation? (not this thread)
Exactly. You see, I have a fairly Eidetic memory. Fine details and patterns usually jump right out at me. 300D wasn't a hard nut to crack, by any means (unless I am dead wrong, which is possible). All the thread he's posted in it's this "I am right and if you disagree with me you are absolutely wrong" thing. His knowledge/interest in Mercedes-Benz diesels was a dead give away. So was his high and might attitude and he is arrogant and pugnacious just like 300D.

Also, the way he types/writes, his grammar, use of punctuation, italic lettering, bold lettering, and spacing- they are identical to 300D's. They mirror 300D's posts even. Also from Denver like 300D (IIRC). Own and his name- "Tormentor". I don't think he likes use very much .

And if you are paying attention you will see he has not yet ONCE denied he is 300D. Occam's Razor.

Quote:
Originally Posted by Tormentor View Post
I'm sorry. I didn't know you know nothing about engines! Next time I'll give you step-by-step instructions and hold your hand every step of the way.
Quote:
Originally Posted by Tormentor View Post
Again, I'm sorry for assuming the people here are smart. I didn't realize they were all numbskulls like you. Thanks for pointing it out.
I mean look, classic 300D!. I remember 300D saying pretty much the same to people. Where all idiots, he is so superior. We're not worth his time. I'm going to block you, wahwahwah.

He might as well has just stuck with 300D and dropped his attitude...

Last edited by Smoken Gun; 09-28-2012 at 02:00 AM.
 
Old 09-28-2012, 01:51 AM   #15
Lostnwalmart
 
Lostnwalmart's Avatar

Name: Lostnwalmart
Title: Too Much Time
Status: Not Here
Join Date: Jul 2006
Location: Tokyo Japan
Member`s Gallery
Posts: 8,970
Gosh dang we got us a inspector gadget up in hur!
__________________
Ecorico scooter!!
-Cliff
Quote:
Originally Posted by Snedge View Post
Anybody that would not haul a dinosaur for an orphanage is no friend of mine.
To some people it's all about money. Geez
Click the image to open in full size.
 
Old 09-28-2012, 01:53 AM   #16
Smoken Gun
 
Smoken Gun's Avatar

Name: Smoken Gun
Title: Diaboli parum adiutor.
Status: Not Here
Join Date: Nov 2010
Location: Michigan
Member`s Gallery
Posts: 3,200
I like to think of myself as more of a Sherlock Holmes. You wanna be Watson there Kliperd?
 
Old 09-28-2012, 02:56 AM   #17
Lostnwalmart
 
Lostnwalmart's Avatar

Name: Lostnwalmart
Title: Too Much Time
Status: Not Here
Join Date: Jul 2006
Location: Tokyo Japan
Member`s Gallery
Posts: 8,970
You know I would use any chance possible to use a monocle and an outrageous British accent! so what does your deductive reasoning tell you holems
__________________
Ecorico scooter!!
-Cliff
Quote:
Originally Posted by Snedge View Post
Anybody that would not haul a dinosaur for an orphanage is no friend of mine.
To some people it's all about money. Geez
Click the image to open in full size.
 
Old 09-28-2012, 03:09 AM   #18
Smoken Gun
 
Smoken Gun's Avatar

Name: Smoken Gun
Title: Diaboli parum adiutor.
Status: Not Here
Join Date: Nov 2010
Location: Michigan
Member`s Gallery
Posts: 3,200
That we need to find a "monocle guy" pronto tonto! Possibly a wig and mustache guy as well.
 
Old 09-28-2012, 03:47 AM   #19
Tormentor

Name: Tormentor
Title: Banned
Status: Not Here
Join Date: Jun 2012
Location: Denver
Member`s Gallery
Posts: 298
Quote:
Originally Posted by Smoken Gun View Post
Where all idiots
Do they all roam free with you there?
 
Old 09-28-2012, 12:06 PM   #20
oldestof11
 
oldestof11's Avatar

Name: oldestof11
Title: Drag racer
Status: Not Here
Join Date: Jul 2007
Location: Dixon, IL
Member`s Gallery
Posts: 9,084
Quote:
Originally Posted by Tormentor View Post
Welcome to my ignore list.

FYI, the correct username is ForcedInduction. Your mistake is understandable and forgiven, its just another major detail you have completely missed.
Quote:
Originally Posted by 300D
Sorry, their forum is defunct.


Real "experiance" (spelled experience) is exactly what you've found. So please stop acting like a child if you want people to continue helping you.
Hmm....
__________________
Jon
Click the image to open in full size.
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:53 PM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com