Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Dodge Competition and Performance General Dodge Competition and Performance Discussion |
05-13-2017, 03:21 PM
|
#1
|
Name: Penn6.7
Title: Rookie
Status: Not Here
Join Date: Sep 2016
Location: Western Pa
Member`s Gallery
Posts: 8
|
High Rail Pressure at Idle
Just finished building a new engine. 6.7 running 04 electronics, 400% over Injectors, stock LBZ pump over a 12mm 6.7 pump using ATS Controller. Belt on running I'm at max rail, take belt off rail is at demand psi. Replaced pump, FCA and 3 ATS controllers. No improvement. I'm lost. Tested FCA circuit from the ECM and its fine, checked continuity and the wires are good. Certainly it can't be another controller but I have no idea at this point.
|
|
|
05-13-2017, 04:06 PM
|
#2
|
Name: Penn6.7
Title: Rookie
Status: Not Here
Join Date: Sep 2016
Location: Western Pa
Member`s Gallery
Posts: 8
|
That's what I've been hearing.
|
|
|
05-13-2017, 04:45 PM
|
#3
|
Name: Penn6.7
Title: Rookie
Status: Not Here
Join Date: Sep 2016
Location: Western Pa
Member`s Gallery
Posts: 8
|
It's a 6.7 in an 2004 to clear my description up
|
|
|
05-13-2017, 05:29 PM
|
#4
|
Name: Poulina
Title: Too Much Time
Status: Not Here
Join Date: Dec 2015
Location: Norcal
Member`s Gallery
Posts: 795
|
ATS has a reputation of what? I've got nothing bad to say about my ats controller. It does make the truck cough on startup for no apparent reason I will say.
__________________
2008 QCLB 6.8 48re Suncoast PCS, DDP supermentals, forcedinductions 467/87, Hamilton 188/220, Carrillos, studded mains w/stock girdle
|
|
|
05-14-2017, 08:20 PM
|
#5
|
Name: Penn6.7
Title: Rookie
Status: Not Here
Join Date: Sep 2016
Location: Western Pa
Member`s Gallery
Posts: 8
|
Fixed.
|
|
|
05-14-2017, 08:59 PM
|
#6
|
Name: Howling
Title: Soot Sniffer
Status: Not Here
Join Date: Apr 2006
Location: Northern,IL
Member`s Gallery
Posts: 4,304
|
Issue?
Sent from my SCH-I545 using Tapatalk
__________________
Eric
2006 Dodge CTD/48re 4x4 Sport
With some fuel and air.
Bullseye,Hamilton,Exergy,EFI,ATS,FASS,HTS,Thuren, Toyo's...
1996 2500 RC 4x4 CTD-63/68/.83,5X.014,180 maxed Ppump,Fass...
|
|
|
05-19-2017, 10:54 PM
|
#7
|
Name: ctd>therest
Title: Green Behind the Ears
Status: Not Here
Join Date: Jan 2016
Member`s Gallery
Posts: 49
|
How much lift pump pressure do you have? Does it do it when warm? Take the fuse off the lift pump and let it idle. I have a ppe kit my lift pump would make 18psi. My lbz pump would hate it. It would idle at 29k at the rail. But as soon as I take the fuse off the pump. It would go to normal idle pressure.
__________________
2011 rclb ctd/4x4/s482/87fmw/300hp-nozzles/Anarchy-tuned/inglewood-manual-48re/ppe-fuelers/625s
2006 cclb 4x4 some goodies 8.48@82.50mph
|
|
|
05-19-2017, 10:55 PM
|
#8
|
Name: ctd>therest
Title: Green Behind the Ears
Status: Not Here
Join Date: Jan 2016
Member`s Gallery
Posts: 49
|
I went from a ppe to a fish controller it would do the same. I changed the fca from the dmax one to a cummins one didn't help. Until I lowered lift pump pressure to 12psi.
__________________
2011 rclb ctd/4x4/s482/87fmw/300hp-nozzles/Anarchy-tuned/inglewood-manual-48re/ppe-fuelers/625s
2006 cclb 4x4 some goodies 8.48@82.50mph
|
|
|
06-26-2017, 09:08 AM
|
#9
|
Name: Penn6.7
Title: Rookie
Status: Not Here
Join Date: Sep 2016
Location: Western Pa
Member`s Gallery
Posts: 8
|
Sorry for the open ended response. The first pump I had was trashed, replaced the pump, new pump had a bad FCA out of the box which didn't help the troubleshooting process. Replaced FCA and most of the problems went away. Once pressure was under control it was found that the return to tank line was too small for the larger dual pumps. Return size increase and rail returned to normal pressure.
|
|
|
06-27-2017, 07:39 PM
|
#10
|
Name: Jyd302bjj
Title: Green Behind the Ears
Status: Not Here
Join Date: Apr 2017
Member`s Gallery
Posts: 66
|
My ats controller was bad out if the box truck would go to max rail pressure
|
|
|
11-05-2017, 11:49 PM
|
#11
|
Name: EverydayDiesel
Title: I drink diesel
Status: Not Here
Join Date: Feb 2016
Location: $FCE2
Member`s Gallery
Posts: 196
|
I am having a similar issue with mine but the rail pressure is 8-9k at idle.
replaced both fca's
replaced controller to a fish tuning.
i bought an aeromotive 230gph lift pump which recommended a -10an line into a fleece fuel filter bypass then -8an to each pump. I have a -6an return hose. The lift pump is set on the lowest setting (10psi) and at the engine it is reading 4psi (increasing causes the idle pressure to rise) I am thinking that FLOW and psi are not the same as the feed is 5/8". Do I need to add a aeromotive FPR on the return line?
At this point I am a little stumped and would appreciate any help/advice you can give.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 08:56 PM.
|