Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > The Starting Line > Sled Pulling > 2WD Pullers
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 03-07-2012, 10:15 PM   #1
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
Looking for some advice on a 2wd puller.

Ok, well i saw this forum a few days ago, and started reading. Basically i haven't been able to stop thinking about turning my 93 into a puller. I still want to be able to drive the truck on the street. I have been reading this every chance i have gotten. Now as for my truck it's a 93 d350 cab and chassis. it is right over 20ft long. I'm guessing i need to box the frame, get rid of the d70 and get something with a locking differential. need a bigger clutch. meatier tires, ladder bars. mainly looking at ways to get the power to the ground. In my mind there is no point building the engine if i cant get the power to the ground. I am new to pulling, and i probably won't be doing any big pulls, mostly local pulls. well here is the pictures of the truck. there is 11ft from the back of the cab to the back of the bed sorry for it looking so rough, it has been a work truck for 19 years. it will get some body work, and some paint.

Thanks in advanced for all input.

Click the image to open in full size.

Click the image to open in full size.
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-07-2012, 10:31 PM   #2
Bosshawg600
 
Bosshawg600's Avatar

Name: Bosshawg600
Title: PDP.com FireFighter
Status: Not Here
Join Date: Aug 2006
Location: Monticello,In
Member`s Gallery
Posts: 3,651
IMO, that would be a fun 2wd puller!

But you are right, I would put quite a bit of work at first at getting the truck to hold any amount of power! Ditch the D70 and go as big as your wallet allows in the rear. Block the suspension, good traction bars and a well built hitch are going to be next after that.

You can have quite a lot of fun with the VE, but sooner or later its going to need swaped for a nice P Pump, but keep that later down the road.
__________________
2011 Ram Mega, Because my old bones need Comfort!
 
Old 03-08-2012, 01:45 AM   #3
Fireman450
 
Fireman450's Avatar

Name: Fireman450
Title: Daring to be diffrent!!
Status: Not Here
Join Date: Nov 2007
Location: Edmonton , KY
Member`s Gallery
Posts: 1,606
X2 on what Jeff said.
Heres a buddy of mine that fixed His first Gen. He ran a s110 axle and blocked his suspention. had his VE cranked wide open.


And your right its all about putting it all to the ground.
It CAN get expensive...lol (ask me how I know) Ive figured out what stock parts can hold and what is a weak link. Those will show up quick. But any questions ya have we will do our best to answer. It is alot of fun trust me.

Biggest thing is dont get discouraged and have fun.
__________________
Lynn Chapman
Driver: 04.5 CR
Play Toy:1994 Dodge 12V, SMOKE SHOWIN! 2WD Pulling Team. vs. 3.0 in progress. Thanks to Northeast Diesel, MUMAU DIESEL , PullTech Chassis & Fab, Cooper High Performance, SKPP, Joe Gibbs Racing/Driven Racing Oils and all my friends and family!
 
Old 03-08-2012, 02:08 AM   #4
Schrowang
 
Schrowang's Avatar

Name: Schrowang
Title: Schroowwwaaaannnnnggggggg
Status: Not Here
Join Date: May 2011
Location: China, illinois
Member`s Gallery
Posts: 5,887
step one find the rules for the organization you plan to pull with and see what they will allow. you may be limited to a 1-ton rear end, and here you get 30'' hitch height in 2wd. but other than that i agree with the above and mostly have fun with it.
__________________
BRAD
16 F350 platinum
Quote:
Originally Posted by ThatGuy01 View Post
he's not lying anything he'd say on keyboard he'd say in person... Including the great Waffle House dispute that ran Travis off
 
Old 03-08-2012, 04:04 AM   #5
Beebynoid

Name: Beebynoid
Title: Rookie
Status: Not Here
Join Date: Mar 2012
Member`s Gallery
Posts: 13
Is that a solid axle up front? I know the new c&c have a solid axle and a 4 wd conversion is super simple. you literally pull out the front axle put in a drive axle, drive shaft, and the t-case and your done, the worst part would be paying for it but still older 4wd like that have cheap running gear.
 
Old 03-08-2012, 08:20 AM   #6
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
Wow, i did not expect this much responce over night. Thanks

BossHawg- The only thing that i'm not 100% sure on how to do is build ladder bars.

Lynn- Thanks for the video, i will ask questions i know there will be alot.

schrowang-I will look for the local organization.

Beeby- It has an Independant front end. I've heard it is easy to swap, but the parts are hard to find and expensive.
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-08-2012, 10:52 AM   #7
Fireman450
 
Fireman450's Avatar

Name: Fireman450
Title: Daring to be diffrent!!
Status: Not Here
Join Date: Nov 2007
Location: Edmonton , KY
Member`s Gallery
Posts: 1,606
Not a problem it takes a little time. Removable ladder bars wouldnt be that bad to build. There are several threads you can search through to find some really good info on that stuff. Main Diff between 4wd vs 2wd is they need to be longer. Mine come up to almost the front of the cab. Im completely redoing my set up right now so if i can ill snap some pics this weekend.
__________________
Lynn Chapman
Driver: 04.5 CR
Play Toy:1994 Dodge 12V, SMOKE SHOWIN! 2WD Pulling Team. vs. 3.0 in progress. Thanks to Northeast Diesel, MUMAU DIESEL , PullTech Chassis & Fab, Cooper High Performance, SKPP, Joe Gibbs Racing/Driven Racing Oils and all my friends and family!
 
Old 03-08-2012, 01:16 PM   #8
2wpuller
 
2wpuller's Avatar

Name: 2wpuller
Title: letting the smoke fly
Status: Not Here
Join Date: Dec 2006
Location: Washington,Missouri
Member`s Gallery
Posts: 2,880
You guys did a good job covering the basics very well.at this moment I can't think of anything need to add ecept lot of HORSEPOWER. and $$$$$$$$$$$.
you will get alot of help from all of these guys.
Dale
__________________
1975 f250 6.0 Perkins,twins,2006,6sp allison
1972 C10,5.9 5sp
2007 Dodge 2 WD pulling truck
Sponsors
GoerendTransmission
Haisley Machine
MCS MidwestPerformanceDiesel
ShowMePerformance
Snow Performance
 
Old 03-08-2012, 01:39 PM   #9
Schrowang
 
Schrowang's Avatar

Name: Schrowang
Title: Schroowwwaaaannnnnggggggg
Status: Not Here
Join Date: May 2011
Location: China, illinois
Member`s Gallery
Posts: 5,887
everybody loves horsepower!
__________________
BRAD
16 F350 platinum
Quote:
Originally Posted by ThatGuy01 View Post
he's not lying anything he'd say on keyboard he'd say in person... Including the great Waffle House dispute that ran Travis off
 
Old 03-08-2012, 02:16 PM   #10
Bosshawg600
 
Bosshawg600's Avatar

Name: Bosshawg600
Title: PDP.com FireFighter
Status: Not Here
Join Date: Aug 2006
Location: Monticello,In
Member`s Gallery
Posts: 3,651
Oh, and one more thing i would look into.............Most brush pulls wont mind your wheels base at all, but you never know, some people can get all up tight about all kinds of weird things.....


Oh and one other thing I noticed and might want to put this up top. Your going to need a VERY good clutch!!!!!!!!
__________________
2011 Ram Mega, Because my old bones need Comfort!
 
Old 03-08-2012, 02:44 PM   #11
Schrowang
 
Schrowang's Avatar

Name: Schrowang
Title: Schroowwwaaaannnnnggggggg
Status: Not Here
Join Date: May 2011
Location: China, illinois
Member`s Gallery
Posts: 5,887
Quote:
Originally Posted by Bosshawg600 View Post
Oh, and one more thing i would look into.............Most brush pulls wont mind your wheels base at all, but you never know, some people can get all up tight about all kinds of weird things.....


Oh and one other thing I noticed and might want to put this up top. Your going to need a VERY good clutch!!!!!!!!
nonsense, any old clutch will do... once
__________________
BRAD
16 F350 platinum
Quote:
Originally Posted by ThatGuy01 View Post
he's not lying anything he'd say on keyboard he'd say in person... Including the great Waffle House dispute that ran Travis off
 
Old 03-08-2012, 04:15 PM   #12
2wpuller
 
2wpuller's Avatar

Name: 2wpuller
Title: letting the smoke fly
Status: Not Here
Join Date: Dec 2006
Location: Washington,Missouri
Member`s Gallery
Posts: 2,880
Quote:
Originally Posted by Schrowang View Post
nonsense, any old clutch will do... once
__________________
1975 f250 6.0 Perkins,twins,2006,6sp allison
1972 C10,5.9 5sp
2007 Dodge 2 WD pulling truck
Sponsors
GoerendTransmission
Haisley Machine
MCS MidwestPerformanceDiesel
ShowMePerformance
Snow Performance
 
Old 03-08-2012, 10:11 PM   #13
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
pics would be great of the ladder bars, and i will have to upgrade the clutch soon. I can slip it with the mild mods i have now. Do ya'll think I need to upgrade the drive shaft as well? It needs work done, but if i need to go bigger then i don't want to waste money on this one. The u-joints are bigger than the ones that came in most first gens, for some reason it has 2nd gen u-joint, at least i know they're the same as a 3/4 ton 94.
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-08-2012, 10:53 PM   #14
bulldog77
 
bulldog77's Avatar

Name: bulldog77
Title: Too Much Time
Status: Not Here
Join Date: Feb 2010
Location: Southeast South Dakota
Member`s Gallery
Posts: 509
Not to hijack your thread but I also have been looking into doing some of the local pulls. I have been reading on here and looking at pics of other trucks.
This is mine, minus the running boards now
Click the image to open in full size.

Here are the rules for the pullers around my area,


2012 Great Plains Pickup Rules

General Rules

1) All weight added must be fastened securely.
2) If there are any weights or equipment lost during the pull, you will be disqualified.
3) All vehicles will be in neutral or park while being hooked and unhooked, with the drivers’ hands in the air.
4) Two flagman preferred, one at 75' and second at the end of the track, they have the right to stop the pull for any reason.
5) The entire truck must remain in boundaries until the 300' marker or the puller will be disqualified.
6) No passengers will be allowed in the truck while pulling.
7) There will be no class jumping.
8) Classes may be combined providing participation.
9) No split rims allowed.
10) All trucks are subject to a random check at any time.
11) All trucks will start with a tight chain. NO jerking or shifting manual transmissions.
12) All safety equipment needs to be in good working condition.
13) No pulling from the fifth wheel hitch. (Must have clevis with stock hitch).
14) 2 WD and 4 WD may compete in same class depending on participation.

Stock 2 & 4 Wheel Drive

Wt classes 5500, 6500, 7500

1) Pump gas or diesel only. Must be street legal working lights etc.
2) No engine swaps, OEM intake & exhaust manifolds.
3) No strokes allowed. No after-market ignitions.
4) OEM carburetor or fuel injection only.
5) No chips allowed. Stock drive train only.
6) No body swaps or alterations, working flat beds allowed.
7) Must hook from bumper or receiver hitch, must have clevis or pintle eye.
8) Maximum hitch height 2 WD = 30", 4 WD = 27".
9) No lift kits must be factory suspension, no suspension blocks.
10) No weights outside of body.
11) Must meet safety requirements.
12) Tires: DOT 33" High x 13.5” wide max. No cutting or grooving.

Super Stock 2 & 4 Wheel Drive

Wt classes 7500, 8000

1) Any OEM factory production motor within body manufactured under 510 cubic inches.
2) Single carb only, after market carb allowed. Factory fuel injection only, no modifications.
3) Aluminum intake allowed, no tunnel rams or sheet metal intakes, 2" spacer maximum.
4) Factory motor heads only
5) Any type ignition allowed. No magnetos.
6) Engine in stock location.
7) Chips allowed and programs allowed.
8) Must have stock pickup box or full flatbed. Needs to be stock body.
9) Stock frame & wheel base.
10) Traction devices, lift kits & blocking rear suspension allowed.
11) Weights not to exceed more than 60" from center of front axle.
12) Drive shaft loop required on the rear shaft.
13) Maximum hitch height 2 WD = 30", 4 WD = 28 “.
14) Must meet safety requirements, seat belts must be worn.
15) No nitrous, propane, or alcohol. Water methanol allowed.
16) Hitch not to exceed a max rise of 6” and an unlimited drop.
17) Stock receivers must be in good condition with no broken welds or bent tubing, some type of improved
receiver is highly recommended but not required.



Rules and safety rules for all Modified classes.

1) # 2 Fire extinguisher minimum within drivers reach.
2) Master kill switch required 12" or greater above draw bar, no more than 6" off center.
3) White reverse light, lit when in reverse, 2" minimum diameter. Back up horns (alarm) recommended
(but not mandatory).
4) Must have working neutral safety switch.
5) SFI flywheel shield and blanket required on automatic transmissions. SFI steel bell housing required for clutch system. All flywheels must be SFI approved, no gray iron.
6) Drive shaft loops mandatory, 2 per shaft minimum 6" overlap from U joint covers. U joints will be enclosed 360 degrees, 5/16 minimum thickness or complete drive shaft enclosure. Planetary Must have full enclosed shafts, 5/16 steel or 3/8 aluminum.
7) Harmonic balancers to be SFI approved or enclosed with 360 degree shield 1/4 inch thickness to exceed the width of the balancer.
8) Must have engine shields from bottom of head down.
9) No engine driven fans.
10) Upright headers or exhaust only.
11) Wheelie bars mandatory on 2 WD 5"x 5" pad or 25 sq in surface area per pad. Capable of supporting weight of truck no closer than 2 inches behind rear tire with maximum height of 6 inches off the ground.
12) Rear bumper bars and front tow loop required.
13) Full firewall in cab, front and rear glass required.
14) 2wd, no more than 15' from center of rear axle to front most part of truck including weights.
15) 4wd weights no farther than 60" from center of front axle. Hitch point to be no closer than 24" from axle center line. Max of 144" wheel base.
16) Hitch must be ridged in all directions with a 3 x 3 inch hole.
17) Maximum hitch height 2 WD = 30 inch, 4 WD = 27 inch.
18) Must have lug nut covers on rear axle.
19) Lift bodies must have operating doors or escape hatch.
20) Helmets, fire suits, gloves and seat belts required. 5 point harness is preferred.

Modified 2 & 4 Wheel Drive

Wt classes 5500, 6200

1) One automotive style engine in stock location, Maximum 510 cu inches.
2) Any cast head, same make as block. No aluminum heads. In stock configuration, any iron head.
3) Cast block only. Stock boar spacing.
4) Aftermarket intake allowed. Allow tunnel rams. No sheet metal.
5) One carburetor only, any cfm limit. Small blocks can use aftermarket fuel injection.
6) Pump fuel or race fuel only. NO Nitrous.No methanol fuel.
7) Any type ignition allowed. No magnetos.
8) Upright exhaust only.
9) Any rear end. If planetary, it is mandatory enclosed drive shaft.
10) Two transmissions allowed (totally enclosed). Two forms of shifting (only) automatic and rear end.
Allow 2 speed locked on (rear end).
11) Tires, Any DOT or Ag Bar approved tires at 20 PSI, Max of 35 x 16.1 x 16 (110 in circumference)
pro cut tires. No duals, split rims, or professional pulling tires.

Pro Modified 2 & 4 Wheel Drive

Wt classes 6200 Light, 6200 Heavy

1) One automotive style engine in stock location, Maximum 540 cu inches.
2) Any Head except Hemi style head and no 4 valve heads.
3) Naturally aspirated only; any Intake,carbs or injection. No blowers or turbos.
4) Race fuel or alcohol allowed no nitro or nitrous.
5) Any Rear end.
6) Tires, max size equivalent to 18.4 x 16.1 2 WD
7) Tires, max size equivalent to 34 x 15.5 x.15 for 4 WD



Super Modified 2 & 4 Wheel Drive

Wt classes 6200 Light, 6200 Heavy

1) One automotive engine, Blowers, Turbos allowed.
2) Maximum of 2 valves per cylinder
3) All Blowers and turbos must have all straps and shields.
4) 30" drawbar height for both 2 & 4 WD.


Pickup Rules will be in place for 2 years, beginning 2012

__________________
97 12v 2wd auto
97 12v 4wd g56
 
Old 03-08-2012, 11:16 PM   #15
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
Are those rules pretty universal? Is it likely that my local rules will be similar?
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-08-2012, 11:30 PM   #16
bulldog77
 
bulldog77's Avatar

Name: bulldog77
Title: Too Much Time
Status: Not Here
Join Date: Feb 2010
Location: Southeast South Dakota
Member`s Gallery
Posts: 509
These are the rules in the Minnesota area that is near to me.

STOCK DIESEL 8500

1. Stock as delivered from factory

2. Weight bars are prohibited. weight in box only

3. All drivers must have a valid state drivers license.

4. The OEM drivers restraint system is mandatory and must be worn. No passengers allowed

5. The fuel must be a #1 or #2 diesel only . No nitrous oxide, propane, methanol, water or any other oxygen extenders allowed.

6. The hitch must be a factory Resse style hitch. The hitch height from ground may not exceed 26". The hooking point must be horizontal' and must have a minimum 3.00" x 3.75" deep inside diameter opening for sled hook.

7. Stock suspension only. No traction/ladder bars. No blocking, clamping, or preloading of suspension. No air bags If airbags are on truck, compressors must be disconnected and stems removed.

8.The tires must be DOT street tires.

9. Factory STOCK turbo only.

10.Aftermarket air filters and air boxes are permitted. Aftermarket exhaust permitted. Programmers and computer chips permitted.

2.6 Diesel 4x4 Truck

Weight Breaks

2.6: 8000lbs. weight is with driver Minimum weight of 7500lbs.

Regulations

Ballasts:

Ballast is permitted. Front hanging weights are allowed, not to exceed 60 inches forward of the center of front axle. This will be measured from center of front wheels to end of weight assembly ballast may be added in the bed of truck.

Body:

The body must be the OEM truck body, including the full bed floor. The body must retain full sheet metal, aftermarket hoods are permitted. The hood must be closed and securely latched while the vehicle is hooked to the sled.

Brakes:

Four-wheel hydraulic brakes are mandatory.

Chassis:

The OEM chassis is mandatory. The engine must be in the OEM location for the body used. The vehicle must retain the full OEM chassis. Wheel tubs, back-half conversions, tube chassis. ect, are prohibited.

Cooling System:

Radiators must be in the stock location and be of at least stock size.

Credentials:

All drivers must have a valid state driver’s license.

Driveline:

An OEM transmission and transfer case are mandatory. They must have been on a one-ton or smaller pickup.

Driveshaft Loops:

All trucks must have at least six inch wide u-joint shields around the rear u-joint constructed of at least inch steel or 3/8 inch aluminum that will safely contain the u-joint and the end of the rear shaft. All shields must be securely mounted to the vehicle. Any front shaft u-joint that is visible from the side of the truck must be shielded to contain the u-joint and the end of the shaft.

Driver Restraint System:

The OEM restraint system is mandatory and must be worn.

Engine:

The engine is limited to a stock- appearing, Engine and transmissions can be interchanged between Dodge, Ford, and GM as long as they came in a 1 ton truck or less from the factory. Complete engine must have stock appearance except where otherwise noted in these rules. Aftermarket intake manifolds are allowed.

Exhaust:

All vehicles must be equipped to direct exhaust upward. Two 3/8 inch diameter bolts must be placed through the exhaust pipe in a cross pattern within one inch of each other, within 12” of the turbo.

Fire Extinguisher System:

A fire extinguisher system is permitted. It must be securely mounted.

Firewall:

A complete OEM fire wall is mandatory

Floor:

The complete OEM floor pan is mandatory

Fuel:

The fuel must be #1/#2 diesel, Soy/Biodiesel fuel. No propane or NO2 permitted or any other oxygen enhancers.

Fuel Injection Pump:

The fuel injection pump is limited to a stock-appearing, OEM engine model-specific pump only. The use of multiple high-pressure common-rail fuel pumps are legal. Powerstroke engines with a single factory turbo may utilize a second HPOP. Pumps from different years in the same engine model may be interchanged. P7100 pumps are allowed to run RSV (ag governors)

Fuel System:

Racing fuel cells are permitted.

Hitch:

The hitch must be a “Reese”-style hitch; reinforcements are permitted. Trick hitches are prohibited. The hooking point must be the rear most point on the vehicle and must be rearward of the stock location of the tailgate. The hitch must be horizontal to the ground and stationary in all directions. Bumpers may be notched or removed. The hitch’s height from ground may not exceed 26 inches. The hooking point must have a minimum 3.00” wide x 3.75” length inside diameter opening for the sled hook. The hooking point must be a minimum of 44” from the center of the rear axle to the center of the hooking point. The hooking point will be measured to the center of the clevis loop.

Rear End:

Non-OEM rear-end housings are prohibited. It must have been an option on a one-ton or smaller pick up. Rear axle bolts must be covered by a cap or shield.

Steering:

The vehicle must retain the full original OEM steering gear. The vehicle must retain the original power assistance, if it was so equipped. Additional stabilizers are permitted. Non-OEM power assist methods are prohibited.

Suspension, Front:

The upper mounting point for strut assemblies must be in factory location. Adjustable caster/camber pillow ball mounts are permitted. The lower control arm may be strengthened provided factory-mounting points to the chassis are maintained. The lower mounting point for the strut assembly may be modified for improved caster or camber. Strut tower braces, lower tie bars, sway bars, and limiter straps are permitted. Traction bars and devices are permitted.

Suspension, Rear:

An OEM-style suspension is mandatory. Lowering or raising the vehicle height with suspension modifications is permitted. Traction bars and devises are permitted; they must be bolt on only; welds are permitted for attachment to frame or axle housing. All OEM suspension mounting points must be retained and used. Sway bars, limiting straps, and camber kits are permitted. All rear suspensions must use at least one working shock absorber per wheel. Aiebag sprind assistance is permitted; airbag compressors must be disconnected. Blocked suspension is permitted.

Tires:

The tires must be DOT street tires. Cut tires are prohibited. 102” Max outside tire to outside tire.

Transfer Case:

Non-OEM transfer cases are prohibited. The transfer case must have been an opition on a one-ton or smaller pick up truck.

Transmission, Automatic:

Non-OEM transmissions are prohibited. Aftermarket torque converters, valve bodies and internal components are permitted. Transmission brakes are prohibited. Any non-OEM floor mounted automatic transmission shifter must be equipped with a spring-loaded positive reverse lockout device to prevent the shifter from accidentally being put into reverse gear. A functional neutral safety switch is mandatory, All transmission lines must be metallic or high-pressure-type hose. All vehicles using an automatic transmission must be equipped with a transmission shield meeting SFI Spec 4.1 and must be labeled accordingly. A blanket-type shield is permitted; it must be appropriately labeled as meeting SFI Spec 4.1 and it must extend from the rear of the block to the front of the transmission main body the bell housing area is to be completely covered six inch overlap where it is fastened. All non-blanket-type shields must incorporate two ( or one, per manufacturer’s instructions) 3/4” by 1/8” straps that bolt to the shield on each side and pass under the transmission pan unless the transmission pan is labeled as meeting SFI Spec 4.1. All vehicles using an automatic transmission must be equipped with a flex plate meeting SFI Spec 29.1 and be covered by a flex plate shield meeting SFI Spec30.1.

Transmission, Manual:

Non-OEM transmissions are prohibited. Aftermarket internal components are permitted. A clutch meeting minimum SFI Spec 1.1 or 1.2 is mandatory on all vehicles. All manual transmissions must be clutch assisted. Sequential shifters are prohibited. All vehicles equipped with a manual transmission must Have a flywheel shield labeled as meeting minimum SFI Spec 6.3 or greater. Applications for which an SFI Spec flywheel shield is not available may use a properly attached SFI 4.1 or 4.2 blanket that completely covers the bellhousing; it must be attached to the block and extend rearward to the transmission with a minimum six inch overlap where it is fastened.

Turbocharger:

The vehicle is limited to a 2.6” inducer bore single turbocharger. The compressor wheel must protrude into a 2.6” bore for 1/8”. The inlet will be measured using a 2.65” plug the plug must not be able to enter the inducer bore. A stock map width enhancement (MWE) groove is allowed. No MWE groove will be allowed that has a width greater than .200”. All provisions allowing air into the wheel other than via the bore and the MWE groove are prohibited. The vehicle driver will be responsible for making compressor wheel accessible for tech personal to measure bore and be able to inspect compressor wheel.

Water Injection:

Water injection is prohibited. All systems components must be removed from the truck.

Ice Water Intercoolers:

Are Allowed.

Wheelbase:

Maximum wheelbase 158”

3.0 Diesel 4x4 Truck

1. Maximum weight 8000lbs. Minimum weight of 7500lbs.

2. Trucks must remain stock appearing. Must have full size steel or OEM type body. The bed of the truck must have a metal floor, if bed floor is gutted 200lbs. of moveable weight must be placed rearward of the centerline of the rear axle.

3. Maximum engine size will be 460 cubic inch. Engines must come from factory in one ton or smaller Diesel pickup truck. Engine must remain in stock location as intended by manufacturer.

4. Front of engine block can be no farther forward than 17” of centerline of front axle.

5. Hook point must be no closer than 44” of centerline of rear axle, hitch height maximum of 26”, with a minimum of a 3.75” X 3.0” opening. Hitch point must be easily accessed. No “trick” type hitches permitted. Hitch must be stationary in all directions. Hitch must be frame mounted. Hitch must be mounted centerline of rear axle or behind. Hitch must not exceed a maximum of 25 degree angle from pivot point to hook point.

6. One turbo with one pressure stage permitted. Maximum of 3.0” Opening on intake wheel. Map width enhancement is allowed not to exceed .250. Compressor wheel must protrude into three inch bore 1/8”, intake housing may not exceed three inches turbo mounting plates are permitted.

7. Exhaust must exit straight up, with (2) 3/8” bolts mounted in a cross pattern no more than 1” apart as close to the turbine wheel as possible, no more than 6” from turbine wheel.

8. No cast iron clutches or flywheels permitted.

9. Fuel safety kill and or air shutoff must be installed on rear of truck. Kill switch will be securely mounted to the back of the vehicle and have a two (2) inch diameter ring to attach the sled.

10. No fuel lines or tanks permitted inside of truck cab unless securely mounted in marine box.

11. Computer chips and boxes permitted.

12. Fuel Systems Largest fuel injection pump allowed will be a P- Pump with only one plunger per cylinder. ( No Sigma pumps).

13. Must be D.O.T. approved tire. Maximum tire height 35” no studded tires or chains. No alterations to tires allowed. No bar or terra tires. Dual rear wheels are permitted.

14. Water injection permitted.

15. Front weights must be no more than 60” from the center line of the front axle to forward most point and be securely fastened. No weights are allowed in cab of truck if in the bed of truck they are to be securely fastened to bed of truck.

16. Fuel limited to diesel fuel and bio-diesel only. No alcohol, nitrous, propane or any oxygen enhancing agents allowed.

17. Drive train will consist of the following. Any front axle, any transfer case, any rear axle. No planetaries permitted.

18. Axle shields are required. Shield to be .060” thickness steel or aluminum. Shield not to be mounted to axles ends or hub bolts. A hole may be cut in one to allow locking in of hubs.

19. S.F.I. Bell housing Blankets and/or SFI Blow proof Bell housing required.

20. All U-joints must be shielded 360 degrees and with 3/8” thick aluminum or 5/16” thick steel. Shield will be 6” long minimum and centered on U-joint. Inside diameter of shield will be no more than 2 inches larger than U-joint.

21. All intermediate shafts between the transmission and transfer case will be totally enclosed in 3/8” aluminum or 5/16” steel, ” of shaft may be visible.

22. Suspension modifications are permitted. Removable suspension blocks are permitted.

23. Fire Extinguishers, helmets Snell 85 or better, SFI Fire suits, shoes and seatbelts required.

Maximum wheelbase 158” and 102” maximum track width (outside tires to outside tire).

Tech officials will have final say if truck is in question. Safety will not be sacrificed by an unsafe vehicle or driver.


I know the one I posted before is great plains pullers. Thats who is in my area. They are not real picky on there rules. A few of the trucks(24valves, dmax, and psd) were all runnin stock class with tuners. I know for a fact that two of the dodges had aftermarket turbos and traction bars. They all ran stock class and than ran modified.
__________________
97 12v 2wd auto
97 12v 4wd g56
 
Old 03-09-2012, 12:04 AM   #17
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
Ok, i have been reading the Traction bars thread, and i have decided that i will probably Make a set of removable A-frames. only thing is, How long do i need to make them? do i need them to come up to the front of the cab? or would that be too long? I mainly want them removable, because i still plan on being able to drive the truck on the street.
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-09-2012, 01:58 AM   #18
Schrowang
 
Schrowang's Avatar

Name: Schrowang
Title: Schroowwwaaaannnnnggggggg
Status: Not Here
Join Date: May 2011
Location: China, illinois
Member`s Gallery
Posts: 5,887
you want them longgg, mine come to the back of the cab. try for the middle or the front of the cab.
__________________
BRAD
16 F350 platinum
Quote:
Originally Posted by ThatGuy01 View Post
he's not lying anything he'd say on keyboard he'd say in person... Including the great Waffle House dispute that ran Travis off
 
Old 03-09-2012, 08:50 AM   #19
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
alright thanks.
__________________
Shaun

1993 2wd sled dragger.
 
Old 03-09-2012, 10:34 AM   #20
blacksm0king
 
blacksm0king's Avatar

Name: blacksm0king
Title: The Black Smoke King
Status: Not Here
Join Date: Sep 2011
Location: In your closet
Member`s Gallery
Posts: 547
Alright guys, now that i have a general idea (very general, I'll keep researching this) of getting some power to the ground, i need to know how to make the power. I want to know ya'll's opinions on whether i should p-pump the truck from the get-go, or play with the ve for a while. I could also Play with the ve while building a p-pump engine outside the truck, I'm guessing if i went that route, it'd be smart to build a transmission at the same time. Would i be better getting a NV4500, NV5600, G56, or could i go with a transmission out of a f600 or similar truck?
__________________
Shaun

1993 2wd sled dragger.
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:48 PM.

 


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2018, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com