Looking at getting another toy/ project after we close on the next house. I'm wanting something to drag/ street race and possibly a pull here and there. I've had several different makes and models in the past, a dozen 2nd gens, 3rd gens, and a few 6.0 psd. Never been a big dmax guy but I've had a couple. Just looking for feedback, I want something reasonably priced and a plethora of aftermarket support. Will more than likely end up with another 2nd or 3rd gen but just thought I'd post up and get some input. Thanks.
Best make and platform to build off of? Semi budget
- Thread starter thelms
- Start date
Begle1
Active member
You've had dozens of trucks? Why?
Based on your description, you gotta be the most qualified person in the world to answer this question. (Or you're the Chidi Anagonye of the diesel world and each truck you own actually makes you less qualified to answer this question...)
The obvious answer is to have a 24 valve 6.4 Cummins with a mechanical inline pump with dynamic timing, like the Bosch RP39.
Based on your description, you gotta be the most qualified person in the world to answer this question. (Or you're the Chidi Anagonye of the diesel world and each truck you own actually makes you less qualified to answer this question...)
The obvious answer is to have a 24 valve 6.4 Cummins with a mechanical inline pump with dynamic timing, like the Bosch RP39.
Sorry fella didnt mean to hit a nerve.. I've always tinkered with them and got bored. Also far from the most qualified person but I appreciate your enthusiasm. I've been lurking here since 2012 and was just looking for personal experiences and opinions. What is your personal experience with a truck you've built and raced personally...?Would you do it again or go with a different model? If so why?
Last edited:
RD TRCTR
Diesels, Burn Outs & Tits
My opinion, don't do it.
Build a gasser if you're looking to have fun and go fast. A GT5533 on a 5.3 in an S-dime can get you into the low 10's for $20 to $30k.
I have been working on my 06 for far too long now, this year was suppose to be the year until the 'rona came, events were cancelled and my enthusiasm waned.
If I had to do it all over again, I would've left the truck damn near as built by Diamler Chrysler, enjoyed it for what it was and got my pilots license. Or used the money to buy more land. Or put it all into an IRA...
Begle1
Active member
So true. I never want to spend another dime on a vehicle. Nowadays I just want real estate.
SPEEDSHIFT
New member
2006-2007 5.9 Cummins is my vote.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
When you say you want to drag race and pull, go ahead and get rid of the "budget" idea...Those two are polar opposites. Unless you just leave it pretty much stock and just race and pull for the sake of doing it and don't care about going fast or pulling far. Just my $0.02
12valve95
Comp Diesel Sponsor
THIS^^^
I am getting parts together to build a motor for my C30...I am building to be over 500 but under 1000HP 12valve and my cart on PDD site has 10k in it :bang
Now I am probably overbuilding but that does not include any machine work to the block or ANY of the c30 parts....or the wiring, or the fuel cell and parts, or the transmission...custom driveshaft....blah, blah ect, ect.
You cannot really build one of these things for a budget unless you hodgepodge and half ass and that still isn't what I would call cheap!
So to set out to build a race/pull truck....the only budget that exists is a blown one!!
My $.02
Good stuff ^^^^^^. It already has an 11.5 rear and 271 TC and 48re. These are the parts I bought for my 2nd gen.
Maybe build the truck around the 2.5" he351ve for pulling. The Firepunk crew have put crazzy numbers down on the dyno with them. It could still be an easy truck to use for a truck.
Back about 10 yrs ago I had played with a vp44 truck. Pushed it into the 500s and since have kept a 3/4 for pulling but havent done much to them. I've been putting into my IRA and the kids 529 for a couple yrs now, I want to play again.
And yes the s10s can be a riot. I actually had a 89 s10 with a 6.0 ls, 243s, btr cam, backed by a t56. Its was a blast until someone pulled out in front of me n totaled it. I'd post pics if I knew how ha.
Yes, the CRs are a very proven platform. Its crazy to see how far they have came in the past several years. The number with a drop in chargers are impressive (with the supporting mods)
RD TRCTR
Diesels, Burn Outs & Tits
Wow, ok, didn't realize that you were the been there, done it all type of guy.
I recommend that you be cutting edge and go buy a brand new 2021 6.7 Cummins, and push it as far as possible with emissions intact. See how big of injectors and turbo you can go to while keeping everything in place while racing the wheels off of it. Do that, and you will conquer something new for yourself and the diesel industry.