Aluminum Oil Pan Flange

Anyone pondered adding heat sinks to the bottom of one of these where the drain plug is ? Would get good airflow to pull some heat out of the pan/oil ? But not quite as extreme as the cooling tubes in the 6.0 Moroso 28 quart oil pan haha
 
murphy41 said:
Anyone pondered adding heat sinks to the bottom of one of these where the drain plug is ? Would get good airflow to pull some heat out of the pan/oil ? But not quite as extreme as the cooling tubes in the 6.0 Moroso 28 quart oil pan haha
Click to expand...

I've been thinking about doing this to the one I'm building.
 
I ended up building my own flange, cost me so far roughly $21 for material and about 2.5 hrs. I used 3/8x1.0 6061 flatbar.

Maxtorq offered to send me his flanges he had made but I ended up starting to make mine before I heard back from him. But A Big thanks to him for offering.

I drilled as many holes as I could on the ends/corners before welding. I wont use every hole on the side of the block, but will be adding more on the corners.

I'll flip it over and weld the other side then use a flap disc to grind it smooth.

FqafZKklxzorI3W4Q0sAxCJAiB4qiOdUMWKr3GBkyhmp-LHrJpBkw3_hkktb-e_Fwxb_pOc7NQNa3fAlDifiDMH0PodPM2QbIzWIRcMfWw8yKAX4ypPx00U-IwKtf9u4kprPVx-NSsDgN7mLSiK7iWDJrh0SHuYaWuALQf9vWsHURJOyZGQiFEolJXduCV6PWjsOvTmk3DgAZtws5FFNucyX_RZnLWZnVTcoKWlK7ldfngg0Co9oNe5BdbDF4NmcSObZbuQfGfp31r0kheMhosiyw6nO53tPxPZNSq9eLfFWPbtGiQrAjKXkvJob5zRmCfRGsfay7u97_gwFjwsidqPnktLS_4dGgZOGi715YueVBfa5A1Fxbsz5I8VGZpKZmJr6jAsvIp2uFS6Hard1zRf2TsezgByYE6WvR6cQ1Dxaov1aHl9DE8TGYOUGLy9o5RM00fJAwfGnko6X_FxUZOhTVbMWc_aUUO3ntozKCaMRRmXiCAZEY5gdMP5EpplOJ1RB7zaig_e392EJe8O-yMQ-9o5Pip_61G8a045_aolnLVPnWiumTnDW9pd7E8_75GDcnN-lUzZHzWSwwzqC61oT6mLLNUI=w523-h697-no



8YFtFezTwmHYJ1S9SJcZRwVNBrASvrccvjJC0aNTi9W5kHQHjArXGgeKGLa4q2f7YWtKePJX8k42t9WDKD-FdgONuWWrW1Xd0zoFRAd9GFgo5YtoFkb_TnReO8gtkWwpReQxFkiNFFvAgsYW9B1_elBuWg2kEuZ5L3r7jYwItRC3MEiEjtho0ZQfCaEGE39jgiUGbH1bGNdTvS3m0am5Gu4HsL9iykCU-5rEpQTFuY-Tx0Jt55ph8DuNTC6AaBlvt58sT6HZ_u0gK7t2N7zXWYZ90Tzsg1jz1QHCPcYIIkvkaU0D_WLmjJ3E9ivU6wojsSsCkBJIGgTmfnsK_XdJz3DLz7i0-_gliA8qqOyyRIVGxlJMZMwxV2vsghSwmVbGnhr9eTRW-Y53lhdzf8xpMY87pjtGOidtl1VBXk1VcuNws8fgVr9OIcOIA6D9kjFsnSx0GcR7IiTY7tLMDvM0HOrZZfkh9ge88q2vrplHXc9RWbt_hCGybvVR2D38r_iRM3v6KF5WgU9HNWd0jNZjqSTblxelunvDn_DvbTufcyBP5mKjPPgSQzC27HsKcD5aulg-_KBTbFGJUEDHxfIGkptTY9e8Q1Q=w523-h697-no
 
MAXTORQ said:
Pics wont open.

Did you get my email?
Click to expand...

I did Sunday morning (morning after I built my flange), for some reason it was in my spam folder. I usually never think to look in my spam folder. Lesson learned. But Thanks again for offering, possibly someone else could use them.
 
You must log in or register to reply here.
Back
Top