Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Vendor Row > Sponsor Forums > Motorsports Supply
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 08-25-2013, 12:43 PM   #1
COMP461
 
COMP461's Avatar

Name: COMP461
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Apr 2006
Location: Aledo
Member`s Gallery
Posts: 4,008
MaxSpool Engineering and S&T Water Jet and Steel , neat parts

Not sure where my thread on S&T waterjet just went, Must have been a computer glitch, so here it is again
I have been racing with Stan and Matt Thomas for the last 30 years. I have watched Matt come from a little kid around the pits to an accomplished Pro Mod driver.
What I have found, is that Stan and Matt are both Racers and understand what you are describing. S&T has the ability to fast prototype, and make that one off part. The Duramax Valve covers they made needed additional clearance for custom rockers. Matt drew up the spacers and had then in my hand in 30 mins. They have torque plates, girdles, pan rails, valve cover rails, and side cover plates.
The big plate you see on the cutting bed is for a nuclear reactor, as is a lot of S&T’s business. They fit in the performance parts as a service to the racing world, of which they are a part of.

Here is their contact info
S&T steel
4187 Airport Dr
Wichita Falls, Texas 76305
Phone (940) 855-4221
Stan's Thomas
stant3@hotmail.com

I needed NHRA legal spacers, We can make then any Axle, and thichness, and any material

Click the image to open in full size.

I needed spacers for my Duramax Spacers , and in 30 mins they were in my hand


Click the image to open in full size.


Torque plates in aluminum and steel for the Cummins, PowerStroke, Duramax, and even DT466 . this also means copper head gaskets and copper header gaskets



Click the image to open in full size.

RPM sensor holder for Cummins , They also make an adjustable crank sensor bracket

Click the image to open in full size.


The brackets I used when I built the Dr Perfromance Truck

Click the image to open in full size.


thick aluminum for a nuclear power plant , for size referance , notice the 55 gallon drum in the corner , and this is their small waterjet table.

Click the image to open in full size.



here is a few non perfromance aplacations


Click the image to open in full size.


Click the image to open in full size.

Last edited by COMP461; 08-25-2013 at 12:48 PM.
 
Old 08-25-2013, 01:18 PM   #2
oldestof11
 
oldestof11's Avatar

Name: oldestof11
Title: Drag racer
Status: Not Here
Join Date: Jul 2007
Location: Dixon, IL
Member`s Gallery
Posts: 9,081
Funny in your last thread those mounts had Greg at ZZ Fab's name on them.
__________________
Jon
Click the image to open in full size.
 
Old 08-25-2013, 02:07 PM   #3
COMP461
 
COMP461's Avatar

Name: COMP461
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Apr 2006
Location: Aledo
Member`s Gallery
Posts: 4,008
Greg at ZZ is 5 miles away from S&T, they work together. Greg is covered up with Intake manifolds and R&D .
 
Old 08-26-2013, 12:14 PM   #4
COMP461
 
COMP461's Avatar

Name: COMP461
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Apr 2006
Location: Aledo
Member`s Gallery
Posts: 4,008
duramax oil cooler plate
Click the image to open in full size.
 
Old 08-26-2013, 12:46 PM   #5
COMP461
 
COMP461's Avatar

Name: COMP461
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Apr 2006
Location: Aledo
Member`s Gallery
Posts: 4,008
Dmax Valve covers


Click the image to open in full size.
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:25 AM.

 


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2018, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com