Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Tech Area- Dodge > Dodge Tech > 94-98 2nd Gen. 12V
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 10-09-2019, 09:46 AM   #1
SCHMITTY
 
SCHMITTY's Avatar

Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,177
Break over torque spec ?

Just got done with the rotating assembly .020” rebuild. I’ve been using 15/40 and lubriplate 105 together on the bearings. The crank would turn smooth but I have to use both hands to push on the counterweights to get it to turn over.

The clearances are all pretty much in the middle of spec or a hair higher.
__________________
stock 94
 
Old 10-09-2019, 09:51 AM   #2
CorneliusRox
 
CorneliusRox's Avatar

Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Detroit, MI
Member`s Gallery
Posts: 4,154
Depending on how long the assembly lube has been sitting on there, it can get pretty tough to spin by hand.
__________________
Corey - BSME
'21 Tesla Model 3 Perf
'22 DMax AT4 2500
 
Old 10-09-2019, 10:06 AM   #3
SCHMITTY
 
SCHMITTY's Avatar

Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,177
A week or so. I dunked the whole piston into a coffee with 15/40. Is that too much oil ?
__________________
stock 94
 
Old 10-09-2019, 01:05 PM   #4
CorneliusRox
 
CorneliusRox's Avatar

Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Detroit, MI
Member`s Gallery
Posts: 4,154
Oh, you used oil. I got it now. I am not sure. I've had assembly lube get kind of crusty after a month of so.
__________________
Corey - BSME
'21 Tesla Model 3 Perf
'22 DMax AT4 2500
 
Old 10-09-2019, 01:45 PM   #5
SCHMITTY
 
SCHMITTY's Avatar

Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,177
I used lube and oil together on the bearings but I dunked the piston into oil with the rings on and submerged it up to the wrist pin, lined the rings where I wanted and tapped the piston into the block with my sweet new tapered ring compressor
__________________
stock 94
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:33 AM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com