Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Sled Pulling From Street to Pro-Mod, get your Sled Pulling fix here! |
07-31-2006, 04:05 PM
|
#1
|
Name: Bobcat698
Title: Pure Diesel Power
Status: Not Here
Join Date: Apr 2006
Location: Marshfield, WI
Member`s Gallery
Posts: 2,229
|
First hooks on new Driveline/Tcase/Charger, DHRA Missouri pull and WI pull
The Missouri DHRA pull was my first hook with the new 271 Tcase and new drive shafts.
I had a 1 piece 4.095" x .180 wall rear shaft made along with a 3.5" x .083 front shaft, 1.562 stub, using the stock CV.
This shaft setup has been tested to 110MPH in 2WD and works great!
While these were being installed, I also bolted on a Pro-Street 66 charger from High Tech. So far I'm very happy with this trubo, it is very streetable and spools better than my SP66.
Also, I had my converter loosened up a bit when I went to Goerends to have my billet shaft and hub replaced.
Click here to see Video
Missouri DHRA pull, 268 feet. Did not lock the converter, ran 2nd gear unlocked at 3500RPM.
Click here to see Video
Washington County Fair Pull, 308 feet.
This was a 4th place hook. I was unable to get the turbo lit as it was 100 degrees. I ran 2nd gear locked up, worked very well!
I would have been at 3rd place, but the 1st place winner was a Duramax running nitrous (drugs were not allowed, but also weren't checked for) by the time they actually checked his truck, it was about 45 minutes after he pulled, and the nitrous was convienently disconnected.
He pulled 341 feet! 2nd place was 316 feet, a Duramax as well.
Looks like I have some more tuning to do!
|
|
|
08-01-2006, 08:16 AM
|
#2
|
Name: CBSuperDuty
Title: Got Looney???
Status: Not Here
Join Date: Apr 2006
Location: IOWA
Member`s Gallery
Posts: 275
|
Looks good. You will get there. You definately don't have a shortage of fuel.
|
|
|
08-01-2006, 09:56 AM
|
#3
|
Name: house
Title: the Fat kid!
Status: Not Here
Join Date: Apr 2006
Location: Kokomo/Angola, Indiana
Member`s Gallery
Posts: 3,780
|
whats timming set at?
__________________
Joe "House" Kupferschmid
2005 CC LB Dmax ZF6 Puller
2006 CC DRW Dmax Tow Rig
2013 VW Jetta TDI..
|
|
|
08-01-2006, 10:12 AM
|
#4
|
Name: Bobcat698
Title: Pure Diesel Power
Status: Not Here
Join Date: Apr 2006
Location: Marshfield, WI
Member`s Gallery
Posts: 2,229
|
Quote:
Originally Posted by house
whats timming set at?
|
24 degrees buddy..
What are you doing up so early?
|
|
|
08-01-2006, 10:20 AM
|
#5
|
Name: house
Title: the Fat kid!
Status: Not Here
Join Date: Apr 2006
Location: Kokomo/Angola, Indiana
Member`s Gallery
Posts: 3,780
|
bump that sucker up to 27.5
The french canadains has arrived for a milk tank thats why i am up
__________________
Joe "House" Kupferschmid
2005 CC LB Dmax ZF6 Puller
2006 CC DRW Dmax Tow Rig
2013 VW Jetta TDI..
|
|
|
08-01-2006, 11:40 AM
|
#6
|
Name: crzycowboy
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Apr 2006
Location: Painesville, Ohio
Member`s Gallery
Posts: 4,182
|
Good Pulls Garrett.....
__________________
Joshua Stewart / Marketing Manager & Sales
|
|
|
08-02-2006, 10:08 PM
|
#7
|
Name: Bobo
Title: Too Much Time
Status: Not Here
Join Date: Apr 2006
Member`s Gallery
Posts: 434
|
Quote:
Originally Posted by Bobcat698
The Missouri DHRA pull was my first hook with the new 271 Tcase and new drive shafts.
I had a 1 piece 4.095" x .180 wall rear shaft made along with a 3.5" x .083 front shaft, 1.562 stub, using the stock CV.
This shaft setup has been tested to 110MPH in 2WD and works great!
While these were being installed, I also bolted on a Pro-Street 66 charger from High Tech. So far I'm very happy with this trubo, it is very streetable and spools better than my SP66.
Also, I had my converter loosened up a bit when I went to Goerends to have my billet shaft and hub replaced.
Click here to see Video
Missouri DHRA pull, 268 feet. Did not lock the converter, ran 2nd gear unlocked at 3500RPM.
Click here to see Video
Washington County Fair Pull, 308 feet.
This was a 4th place hook. I was unable to get the turbo lit as it was 100 degrees. I ran 2nd gear locked up, worked very well!
I would have been at 3rd place, but the 1st place winner was a Duramax running nitrous (drugs were not allowed, but also weren't checked for) by the time they actually checked his truck, it was about 45 minutes after he pulled, and the nitrous was convienently disconnected.
He pulled 341 feet! 2nd place was 316 feet, a Duramax as well.
Looks like I have some more tuning to do!
|
Third place was a EFI tuned ZF 6 speed Duramax!
Nice vids...that smoke will clear the dragstrip out for sure!
|
|
|
08-03-2006, 09:45 AM
|
#8
|
Name: SuperDave4x4
Title: popcorn playa
Status: Not Here
Join Date: Apr 2006
Location: Luling, Louisiana
Member`s Gallery
Posts: 3,416
|
Nice pulls Garrett! Glad to your back up and running!
So what are the differences in the SP66 and the PS66?
Oh and I'm still trying to decide on that airfilter!!!
__________________
2020 Ram 2500 CCLB 4x4
(Sold)1999 Dodge Ram 2500 4x4 24v CTD Ext. Cab- 01' motor w/ orings, .020 gasket, Garmon/SunCoast, Drag comp, 150hp EDMs, 57/72 twins, AD150, 20" Hoss, Proxes STII, Thuren/Carli, etc
Member #41
|
|
|
08-03-2006, 10:16 AM
|
#9
|
Name: Bobcat698
Title: Pure Diesel Power
Status: Not Here
Join Date: Apr 2006
Location: Marshfield, WI
Member`s Gallery
Posts: 2,229
|
Quote:
Originally Posted by Bobo
Third place was a EFI tuned ZF 6 speed Duramax!
Nice vids...that smoke will clear the dragstrip out for sure!
|
I wasn't sure what 3rd place was.. I just new second was up around 316 feet or so.
It sure will! I might turn it back a bit.. Some people think I may have too much.. Drowning out the turbo possibly.
|
|
|
08-03-2006, 10:18 AM
|
#10
|
Name: Bobcat698
Title: Pure Diesel Power
Status: Not Here
Join Date: Apr 2006
Location: Marshfield, WI
Member`s Gallery
Posts: 2,229
|
Quote:
Originally Posted by SuperDave4x4
Nice pulls Garrett! Glad to your back up and running!
So what are the differences in the SP66 and the PS66?
Oh and I'm still trying to decide on that airfilter!!!
|
Thanks!
Oh no, not another Acronym that could be mistaken for II's turbos...
The Pro Street 66 charger has a 71mm exhaust wheel, compared to the Sled Puller 66 that has a 67mm wheel. My experience has been lowered EGT's, more fun to drive in town, and overall nicer exhaust tone!
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 07:04 AM.
|