Sarafin
New member
Moving shops and going trough our attics, posting things that dont need to make the trip to the new shop!
Dodge Grill, i believe it fits 13-18 1500s -$50
Fuel cell, this is huge i think its 10 gal. comes with all the an fittings and shut off on the bottom - $150
5 Speed center console I hacked a slit in it so it isnt perfect, comes with shifter boot but i dont believe i have the t-case boot, if i come across it itll go with it - $25
2nd Gen Dash came out working, should be around 200K on the odo - $25
Blown up Columbus HX60, rebuildable needs a new exh. wheel, inducer and cover touched up. turbo experienced unscheduled disassembly due to a lack of petroleum lubrications. has a T6 1.29 exh housing - $250
HX60 3.0 SB wheel and cover - Oh wow how convenient that all you'll need is a exhaust wheel and rebuild and you have a turbo, I was told its an old bullseye wheel, looks to be in decent shape -$150
5.9 Cummins stock harmonic balancer machined for autometer Tach pickups
Autometer 5" Diesel memory tack, comes with dash switch but no pickup leads or pickup, Came off truck working - $150
10 (TEN) 12v stock length MaxSpool Push rods, once again this is for 10, not a complete set - $40
Back of head block off for 12v, sweet little factory pice off a f500 12 with a output to the pass side if you want a coolant outlet at the back of the head - $25
12v P7100 Shut off solenoid, was working when removed - $40
CPP 165# Springs, never used will come with sticker - $75
Copper spray pipe, I used this on the return of my a/w coooler, I believe its 3/4 npt - $25
DTT Assassin lift pump, worked when removed, only whats pictured, no lines or check valves - $100
T4 to T6 with blowoff flange - $75
Coolant setup, Meziere pump, Derale dual cooler (i i origaly cooled both head water and oil in this cooler then changed to only cooling water) and a summit tank that took a good dinger. will come with all lines and fittings. was in my 2nd gen puller with rad mounted pass side grill, tank driver side behind the headlight and the pump was low below the grill driver side. - $200
12v Runner intake lines, super nice bends bought them before I went to deckplate, haven't test fit them - $500
2 different S400 cores, one looks to have been drilled and tapped for a shaft rom sensor, other one not, they have different oil outlets aswell. feel free to correct me if theyre different centers, - $50/ per
S400 1.32 Exh housings. I have one of all outlets, marmon, half maromon, and ones a flat v band style all T6, all 1.32 - $50/ Per
Ill work on pictues to be below.
All prices and not including shipping, buyer pays like we all know.
My cell is (413)563-nine2five6
Located in Western Mass
The more you buy the more Ill work with you.
Thanks!
Dodge Grill, i believe it fits 13-18 1500s -$50
Fuel cell, this is huge i think its 10 gal. comes with all the an fittings and shut off on the bottom - $150
5 Speed center console I hacked a slit in it so it isnt perfect, comes with shifter boot but i dont believe i have the t-case boot, if i come across it itll go with it - $25
2nd Gen Dash came out working, should be around 200K on the odo - $25
Blown up Columbus HX60, rebuildable needs a new exh. wheel, inducer and cover touched up. turbo experienced unscheduled disassembly due to a lack of petroleum lubrications. has a T6 1.29 exh housing - $250
HX60 3.0 SB wheel and cover - Oh wow how convenient that all you'll need is a exhaust wheel and rebuild and you have a turbo, I was told its an old bullseye wheel, looks to be in decent shape -$150
5.9 Cummins stock harmonic balancer machined for autometer Tach pickups
Autometer 5" Diesel memory tack, comes with dash switch but no pickup leads or pickup, Came off truck working - $150
10 (TEN) 12v stock length MaxSpool Push rods, once again this is for 10, not a complete set - $40
Back of head block off for 12v, sweet little factory pice off a f500 12 with a output to the pass side if you want a coolant outlet at the back of the head - $25
12v P7100 Shut off solenoid, was working when removed - $40
CPP 165# Springs, never used will come with sticker - $75
Copper spray pipe, I used this on the return of my a/w coooler, I believe its 3/4 npt - $25
DTT Assassin lift pump, worked when removed, only whats pictured, no lines or check valves - $100
T4 to T6 with blowoff flange - $75
Coolant setup, Meziere pump, Derale dual cooler (i i origaly cooled both head water and oil in this cooler then changed to only cooling water) and a summit tank that took a good dinger. will come with all lines and fittings. was in my 2nd gen puller with rad mounted pass side grill, tank driver side behind the headlight and the pump was low below the grill driver side. - $200
12v Runner intake lines, super nice bends bought them before I went to deckplate, haven't test fit them - $500
2 different S400 cores, one looks to have been drilled and tapped for a shaft rom sensor, other one not, they have different oil outlets aswell. feel free to correct me if theyre different centers, - $50/ per
S400 1.32 Exh housings. I have one of all outlets, marmon, half maromon, and ones a flat v band style all T6, all 1.32 - $50/ Per
Ill work on pictues to be below.
All prices and not including shipping, buyer pays like we all know.
My cell is (413)563-nine2five6
Located in Western Mass
The more you buy the more Ill work with you.
Thanks!
