Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Vendor Row > Sponsor Forums > Fleece Performance Engineering
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 09-04-2011, 10:33 AM   #1
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
No instructions for fleece controller..?

Just like the title reads. I didnt get the instructions for my fleece controller to run on an 04 cr. I know these things are pretty much self explanatory but being that I'm not very familiar with cr's I'm not sure on the connections. I know the lead that hooks to the controller on the turbo isnt quite right, as I'll have to shave the plastic guides in order for it to connect. But my question is for the three leads hanging together, where do they go. I'm gonna guess map, but that will only use two of the three. Second question is for the red and black wires, can I just use ignition Pwr and ground or is that somethin specific as well. I know all this seems very ignorant to post but I have no way of contacting fleece today and need to get the truck out of here. Any help would be huge and greatly appreciated. I'll pm my # to anybody who could help. Thanks,
 
Old 09-04-2011, 10:47 AM   #2
srt6
 
srt6's Avatar

Name: srt6
Title: sittin on the side line
Status: Not Here
Join Date: Mar 2011
Location: marshall, tx
Member`s Gallery
Posts: 327
(765) 676-5063 i googled fleece performance, its not hard to find a phone number these days unless your brain dead, but anyhow here's the number they will help you
__________________
2012 F250 KING RANCH FX4, STOCK, 4" LIFT, 35's/20's
06 DODGE QC 11.33 @ 120 mph ....sold
 
Old 09-04-2011, 11:04 AM   #3
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Listen jack wagon, your attempt at sarcasm has left you in a vulnerable position to be made the brain dead retard you seem to know so well. Read the post and don't comment on it until your capable of comprehending what it's saying. The post was put up today, in this country it's Sunday. Sunday means closed. Closed means I'll be unable to contact them. Post specifically reads "today". Go fuk yourself you ignorant prick.
 
Old 09-04-2011, 11:07 AM   #4
kleann
 
kleann's Avatar

Name: kleann
Title: VP44 pwr
Status: Not Here
Join Date: Aug 2008
Location: Down yonder
Member`s Gallery
Posts: 4,326
Quote:
Originally Posted by buzzin1/2dozen View Post
Listen jack wagon, your attempt at sarcasm has left you in a vulnerable position to be made the brain dead retard you seem to know so well. Read the post and don't comment on it until your capable of comprehending what it's saying. The post was put up today, in this country it's Sunday. Sunday means closed. Closed means I'll be unable to contact them. Post specifically reads "today". Go fuk yourself you ignorant prick.
But you need to put this in the tech section or dodge performance, pm a mod.

Last edited by kleann; 09-04-2011 at 11:10 AM.
 
Old 09-04-2011, 11:13 AM   #5
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
I appreciate the advice. This is gonna sound dumb, but can I transfer this thread to there or do I new to just repost. Never had to do this before. Thanks
 
Old 09-04-2011, 11:14 AM   #6
kleann
 
kleann's Avatar

Name: kleann
Title: VP44 pwr
Status: Not Here
Join Date: Aug 2008
Location: Down yonder
Member`s Gallery
Posts: 4,326
Quote:
Originally Posted by buzzin1/2dozen View Post
I appreciate the advice. This is gonna sound dumb, but can I transfer this thread to there or do I new to just repost. Never had to do this before. Thanks
You can't transfer it yourself, I see that wunderwood is on right now, pm him, he should be able to move it.
 
Old 09-04-2011, 11:35 AM   #7
TMONEYDIESEL
 
TMONEYDIESEL's Avatar

Name: TMONEYDIESEL
Title: TURBOS BABY!!
Status: Not Here
Join Date: Jan 2007
Member`s Gallery
Posts: 8,664
I moved it
__________________
MANNING MOTORSPORTS
Office +1 (512) 217-7644

YOUR SOURCE FOR:
Custom Camshafts
Billet Pushrods
Valve springs
Custom Turbos
Exhaust Manifolds
Custom Injectors
Carrillo Connecting rods
 
Old 09-04-2011, 11:40 AM   #8
impmouse
 
impmouse's Avatar

Name: impmouse
Title: loaf
Status: Not Here
Join Date: Nov 2006
Location: FISHERS,IN
Member`s Gallery
Posts: 940
i agree with buzzin ,, and monday is labor day , closed then to

bump for ya..
 
Old 09-04-2011, 12:42 PM   #9
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Good deal, I appreciate the help guys
 
Old 09-04-2011, 01:55 PM   #10
lcaad1249
 
lcaad1249's Avatar

Name: lcaad1249
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: Cape Girardeau, MO
Member`s Gallery
Posts: 963
Jim, not sure if the Diesel Power writeup would help, but here it is:
Equipping A '99 Dodge Ram With A Variable-Geometry Turbo - Diesel Power Magazine
__________________
2004.5 Ram 2500, 6.7 swapped, Smarty Touch with Firepunk UDC, Exergy 200%, MPI 64/71/13SS over S480 w/racecover, AD150, PPE Dual Fuelers, Dave Goerend Transmission

1999 Ram 2500, DPE P-pump, 7x.014, Ported head, 14mm studs, Fireringed, Full Billet HTS
 
Old 09-04-2011, 06:03 PM   #11
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
I appreciate all the help guys. The 3pin connector I supposed to plug into the can bus signal, but that still leaves the other two which are supposed to piggy back the map sensor. I'm wondering if I have the wrong harness since the two connectors are Completley different from the maps. It's all hooked up now and I can controll the exhaust brake fine. And when the dial reaches 100% it seems to do the same thing at 0% fueling. The test drive however was horrible. I made a total of 10lbs of boost and a high pitch squeal at WOT. No good. Anyhow the turbo seems ok by play and egt's never went over about 800.. Wtf. It has to be this map pigtail. The diesel power ad was helpful but didn't reveal everything, but I really appreciate it. Not sure what's next, maybe trim this grey hair...
 
Old 09-04-2011, 06:23 PM   #12
SINNER
 
SINNER's Avatar

Name: SINNER
Title: BallSoHard U
Status: Not Here
Join Date: Feb 2007
Location: The Un Free State
Member`s Gallery
Posts: 4,803
The website says all 3 wires hook to the datalink connector. I do not think that is the CANBUS but the proprietary Cummins connector. That is a 3 pin plug coming out of the harness down at the ECM.
__________________
2004 f-350 cc drw

Build a man a fire and he'll be warm for a day...

Set a man on fire and he'll be warm for the rest of his life.
 
Old 09-04-2011, 07:06 PM   #13
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Ok, Im hooked into that connector, just didnt know the name. There is only one female connector on the fleece controller and it has to fit the engine connector. Phucked up thing is on all three of my fleece connectors there are only 2 wires fed into the three wire connector. The engine connector is three wire. My other two fleece connectors are both male. I've looked and looked but cannot find any alternative to using these connectors.

Did just notice that of the two (at this point unused) male connectors the pins inside are male on one and female on the other. Man the instructions would be awesome.
 
Old 09-04-2011, 07:16 PM   #14
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
I'm pressty sure this harness is for an 02. I don't have an 02 to verify my point but hear me out. The 02's also have a similar connector behind the vp and down a little bit with a dummy cap on it that would fit my fleece harness now. That would mean I'd have to use one of the male fittings on that data connector. The other male and female connector would be used as the map fooler, as they are the same style plug in as the 02's map. Man I hope I'm wrong but that certainly makes sense.

Of this entire system I can only find one three pin connector that fits my harness. I believe on an 02 there'd be two..
 
Old 09-04-2011, 07:19 PM   #15
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Nevermind, that's as accurate as Randy savage throwing a butt dart. The maps on 02's are smaller, way smaller
 
Old 09-04-2011, 07:59 PM   #16
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Can anyone tell me the name of the guy on here who works for fleece? I know it's late but if he's got a minute maybe I could pm him and just resolve this issue. I'm over it
 
Old 09-04-2011, 09:01 PM   #17
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
TTP
 
Old 09-04-2011, 09:41 PM   #18
bobcat67
 
bobcat67's Avatar

Name: bobcat67
Title: Diesel Enthusiast
Status: Not Here
Join Date: Dec 2008
Location: Billings, MT
Member`s Gallery
Posts: 163
i hate to put a link from this site on here but i'm gonna, this might help,
Fleece vgt installed - Dodge Cummins Diesel Forum
__________________
2013 F350
1998 Ram 2500
 
Old 09-04-2011, 10:17 PM   #19
AH64ID
 
AH64ID's Avatar

Name: AH64ID
Title: Too Much Time
Status: Not Here
Join Date: Dec 2008
Member`s Gallery
Posts: 882
Quote:
Originally Posted by buzzin1/2dozen View Post
Can anyone tell me the name of the guy on here who works for fleece? I know it's late but if he's got a minute maybe I could pm him and just resolve this issue. I'm over it
I think this is who you are looking for.

Competition Diesel.Com - Bringing The BEST Together
__________________
2005 Cummins, QCLB, 4x4, NV5600, GT3782R, Hamilton 178/208, Smarty UDC, BBi Stage 1

 
Old 09-04-2011, 11:47 PM   #20
buzzin1/2dozen

Name: buzzin1/2dozen
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2010
Location: Northern indiana
Member`s Gallery
Posts: 104
Awesome, I sent em a pm. Thanks for the help!
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:52 PM.

 


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2018, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com