Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Vendor Row > Sponsor Forums > Intelligent Engineering
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 09-25-2008, 11:00 PM   #1
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
BK bypass kit/assemble

Pic of current common kit Assy
Attached Images
File Type: jpg Bypass Kit.JPG (39.1 KB, 300 views)
 
Old 09-25-2008, 11:09 PM   #2
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
Bypass block on Bracket

Bypass is installed at a 45degree clocking using included hardware. Required wrench size ½” washers are to be used next to red anodized block. The Brkt has three different adjustment heights the middle one is the one shown. The bracket has one leg longer than the other it is to be aft. The Regulator block can be used on either side of the bracket as required. The majority of the time it will be on the Passenger side of the bracket. Third Gens using stock heads bolts can use OEM nuts to install bracket. Removing OEM heat shield is recommended as well. All other installs may need to get two longer exhaust bolts to make up for the ¼” 304 stainless plate. In some twin turbo trucks it maybe required to bend the plate for clearance reasons. The plate comes with reliefs that make this possible.
The Ports on the block are numbered. Number 1 faces front and number 2 is aft. Another easy way to ensure correct oreintation is to make sure the plated regulator is facing forward and down.
Attached Images
File Type: jpg Bypass on Brkt.JPG (34.4 KB, 78 views)
 
Old 09-25-2008, 11:14 PM   #3
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
Bypass with Fittings

45* Fittings are oringed, fittings are to be run down to oring and correctly clocked opposite each other. A backing wrench 1 19/64 (Cresent Wrench) is needed when tightening the 1 ½“ locking nuts.
Attached Images
File Type: jpg Bypasswithfittings.JPG (27.0 KB, 90 views)
 
Old 09-25-2008, 11:17 PM   #4
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
Head Supply Port Fitting Assy.

The fitting that goes into the head wrench size is 15/16”. Recommend using teflon thread sealant on npt threads of fitting that goes into head. (This fitting replaces OEM plug that is located between on aft, top, passenger side of head between cylinders 5 & 6.)
Next is the 90* elbow requries a 1” wrench and a 7/8” backing wrench. The JIC 12 adapter requires a 1 1/8” wrench. Pushlock fittings require 1 ¼ wrench.
Attached Images
File Type: jpg HeadfittingAssy.JPG (25.1 KB, 47 views)
 
Old 09-25-2008, 11:24 PM   #5
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
Return Splice

Requires 1 1/16" wrench and teflon thread sealant recommended on npt threads of fitting that goes into splice. Aluminized steel tubing splice comes unpainted. Some twin turbo trucks are welding a ½” npt bung to the water return line. Instead of a hose splice they will receive a adapter fitting and 90* push lock fitting.
Attached Images
File Type: jpg Bypass Install 007.jpg (35.3 KB, 49 views)
 
Old 09-25-2008, 11:28 PM   #6
Opie
 
Opie's Avatar

Name: Opie
Title: Ingenuity Director
Status: Not Here
Join Date: Apr 2006
Location: Federal Way, WA
Member`s Gallery
Posts: 363
Hose Discoloring

The color blue and black are smooth and the outside over time has shown discoloration. The red and grey color hose have yet to show discoloration. A few owners are supplying their own stainless lines. To do so requires AN 12fittings and in most cases about 5’ of ¾ in i.d. line.

The color blue is by far the most popular color used.
Attached Images
File Type: jpg HoseDiscolorization.JPG (25.1 KB, 76 views)
 
Old 09-26-2008, 05:00 AM   #7
Jim Fulmer
 
Jim Fulmer's Avatar

Name: Jim Fulmer
Title: Too Much Time
Status: Not Here
Join Date: May 2006
Location: Quanah Tx.
Member`s Gallery
Posts: 5,013
Nice post Steve, very well thought out.

Jim
__________________
01' 12V, S/B, Q/C, 4WD
98' 12V, S/B, Q/C, 2WD
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:20 PM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com