Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
09-18-2013, 11:42 AM
|
#1
|
Name: EricStaab
Title: Sponsor
Status: Not Here
Join Date: Sep 2012
Location: WI
Member`s Gallery
Posts: 255
|
24V Cummins with No Limit Camshaft
This truck runs in the 2.6 class. It is only a reground camshaft. We made it a little conservative based on the engine build up front, but we are going to give it an upgrade this winter with a steel core, and little bigger cam profile.
Typically turns about 4800 rpm.
__________________
No Limt MFG,
Manufacturer of diesel performance engine parts: Billet camshafts, rods, valvetrain components, cylinder heads. We take on the hard and unusual jobs no one else is willing to do.
Website: NoLimitMfG
Facebook: Nolimitmfg
Phone:715-384-4422
|
|
|
11-14-2013, 07:42 PM
|
#2
|
Name: DodgeDude55
Title: Too Much Time
Status: Not Here
Join Date: Mar 2013
Location: Waterford,WI
Member`s Gallery
Posts: 395
|
How much would one of these cams cost a guy? I'll b in the market for a cam this winter. This will b for a 2005 pulling in 2.5 class
__________________
2005 Dodge Ram 2500- 3.0 smooth bore puller
2011 Ram 2500- tow rig/ daily driver
|
|
|
11-15-2013, 08:11 AM
|
#3
|
Name: EricStaab
Title: Sponsor
Status: Not Here
Join Date: Sep 2012
Location: WI
Member`s Gallery
Posts: 255
|
We have a few options for you. A reground cam is $275.00, with customer supplied core. We also will have steel billet cams ready in December. Our off the self billet cams are $650.00. If you pre order this month they are $600.00 These are not a cast cam. They are steel. So you would need to compare them to Hamiltons $700 and up camshafts.
These are what grinds we offer for our off self cams.
186-209 107.5LSA .295/.310 Lift
187-220 108.5LSA .306/.322 Lift - Largest cam with out cutting pistons.
226-240-106.5LSA .330/.340 Lift requires piston cuts.
If you want a custom grind on a billet cam core the price is $800.00. If you pre order this month they are $750.00 We custom grind these to match your combination!
__________________
No Limt MFG,
Manufacturer of diesel performance engine parts: Billet camshafts, rods, valvetrain components, cylinder heads. We take on the hard and unusual jobs no one else is willing to do.
Website: NoLimitMfG
Facebook: Nolimitmfg
Phone:715-384-4422
|
|
|
11-15-2013, 11:29 AM
|
#4
|
Name: Badbrad3701
Title: Borrowed Money
Status: Not Here
Join Date: Oct 2012
Location: South bloomingville, Ohio
Member`s Gallery
Posts: 646
|
What cam was in the truck in video above?
|
|
|
11-15-2013, 12:19 PM
|
#5
|
Name: DodgeDude55
Title: Too Much Time
Status: Not Here
Join Date: Mar 2013
Location: Waterford,WI
Member`s Gallery
Posts: 395
|
Where are you located in wisconsin?
__________________
2005 Dodge Ram 2500- 3.0 smooth bore puller
2011 Ram 2500- tow rig/ daily driver
|
|
|
11-15-2013, 04:24 PM
|
#6
|
Name: EricStaab
Title: Sponsor
Status: Not Here
Join Date: Sep 2012
Location: WI
Member`s Gallery
Posts: 255
|
Quote:
Originally Posted by Badbrad3701
What cam was in the truck in video above?
|
We reground his stock cam. When he was originally putting the motor together, he wanted to daily drive the truck, and was thinking he would only be able to turn 4k.
So we ground him something moderate. 190s int. low 200s exh. durations I believe.
Turns out it typically runs 4800 rpm.
__________________
No Limt MFG,
Manufacturer of diesel performance engine parts: Billet camshafts, rods, valvetrain components, cylinder heads. We take on the hard and unusual jobs no one else is willing to do.
Website: NoLimitMfG
Facebook: Nolimitmfg
Phone:715-384-4422
|
|
|
11-15-2013, 04:25 PM
|
#7
|
Name: EricStaab
Title: Sponsor
Status: Not Here
Join Date: Sep 2012
Location: WI
Member`s Gallery
Posts: 255
|
Quote:
Originally Posted by DodgeDude55
Where are you located in wisconsin?
|
I'm located in Marshfield, WI.
__________________
No Limt MFG,
Manufacturer of diesel performance engine parts: Billet camshafts, rods, valvetrain components, cylinder heads. We take on the hard and unusual jobs no one else is willing to do.
Website: NoLimitMfG
Facebook: Nolimitmfg
Phone:715-384-4422
|
|
|
11-15-2013, 09:05 PM
|
#8
|
Name: DodgeDude55
Title: Too Much Time
Status: Not Here
Join Date: Mar 2013
Location: Waterford,WI
Member`s Gallery
Posts: 395
|
I think I'm guna take my business to you local guys on this. How much time does it take to get a custom billet cam made
__________________
2005 Dodge Ram 2500- 3.0 smooth bore puller
2011 Ram 2500- tow rig/ daily driver
|
|
|
11-16-2013, 08:07 AM
|
#9
|
Name: EricStaab
Title: Sponsor
Status: Not Here
Join Date: Sep 2012
Location: WI
Member`s Gallery
Posts: 255
|
Our steel cores will be ready in December. So once they are in then we finish grind them. It would take about 1 week to turn around once we have the cores. Also will help if you have all your information to us before the cores arrive, so we can work on developing your lobe profile.
Here is a link to our cam data form. http://nolimitmfg.com/performance-pr...ollection-form
__________________
No Limt MFG,
Manufacturer of diesel performance engine parts: Billet camshafts, rods, valvetrain components, cylinder heads. We take on the hard and unusual jobs no one else is willing to do.
Website: NoLimitMfG
Facebook: Nolimitmfg
Phone:715-384-4422
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 09:56 AM.
|