Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
John Deere The Green machines |
03-26-2011, 02:14 PM
|
#1
|
Name: kalder
Title: Kevin Alder
Status: Not Here
Join Date: Oct 2006
Location: Kittitas Valley, WA
Member`s Gallery
Posts: 1,286
|
R450 Swather
We are having a problem with the hydro handle.
I want to move the header tilt function to the Honeybee control. The switches are in a circuit board and wired in a matrix fashion. So I can't just switch some pins around in the handle electrical connector.
So, I was trying to figure out if I could build a harness that goes from the Honeybee header command connector, to the tilt valve solenoid.
My problem is I can't find any schematics on the Honeybee connector in Service Advisor. Honeybee has one on their site but doesn't help.
Another question is will my harness work with the CAB controller programmed to the 4.5 meter rotary header? Or will I have to program it to the Honeybee header? If I program it to the Honeybee, will the rotary header function properly?
We have three guys with the same problem, three different machines. It is all operator error, but if I could make it easier for them, it would be awesome.
When they get to the end of a row, and lift the header, they bump the tilt. When they put it down they are swathing dirt.
Thanks in advance!
__________________
Kevin
03 3500
|
|
|
03-26-2011, 03:14 PM
|
#2
|
Name: kalder
Title: Kevin Alder
Status: Not Here
Join Date: Oct 2006
Location: Kittitas Valley, WA
Member`s Gallery
Posts: 1,286
|
__________________
Kevin
03 3500
|
|
|
03-26-2011, 03:36 PM
|
#3
|
Name: kalder
Title: Kevin Alder
Status: Not Here
Join Date: Oct 2006
Location: Kittitas Valley, WA
Member`s Gallery
Posts: 1,286
|
Oops. I thought the labeling was there
__________________
Kevin
03 3500
|
|
|
04-12-2011, 11:27 AM
|
#4
|
Name: cumminspuller
Title: diesel junky
Status: Not Here
Join Date: Apr 2008
Location: Fayetteville, Tn
Member`s Gallery
Posts: 1,259
|
I wish I could help you man but I'm out on this one. All I could do is speculate.
__________________
07 Dodge 2500 reg cab 6.7 auto 4wd
97 Dodge 3500 reg cab flatbed 5spd 4wd
|
|
|
04-13-2011, 09:27 PM
|
#5
|
Name: bosshogg
Title: Running with the best...
Status: Not Here
Join Date: Nov 2009
Location: Franklin, OH
Member`s Gallery
Posts: 510
|
I'm guessing you have been in touch with DTAC and they have been ZERO help as per usual?
__________________
2013 2500 Crew/Long 6.7 68RFE NV273 stock until 2018
2011 Jeep CJ7 304/T18/D300. D44's F&R on 35x12.50's
|
|
|
04-15-2011, 08:48 AM
|
#6
|
Name: cumminspuller
Title: diesel junky
Status: Not Here
Join Date: Apr 2008
Location: Fayetteville, Tn
Member`s Gallery
Posts: 1,259
|
Quote:
Originally Posted by bosshogg
I'm guessing you have been in touch with DTAC and they have been ZERO help as per usual?
|
That is 100% true!!
__________________
07 Dodge 2500 reg cab 6.7 auto 4wd
97 Dodge 3500 reg cab flatbed 5spd 4wd
|
|
|
04-15-2011, 09:02 AM
|
#7
|
Name: kalder
Title: Kevin Alder
Status: Not Here
Join Date: Oct 2006
Location: Kittitas Valley, WA
Member`s Gallery
Posts: 1,286
|
DTAC is no help here.
__________________
Kevin
03 3500
|
|
|
04-15-2011, 09:06 PM
|
#8
|
Name: bosshogg
Title: Running with the best...
Status: Not Here
Join Date: Nov 2009
Location: Franklin, OH
Member`s Gallery
Posts: 510
|
I'm betting you are going to wind up pulling that circuit board out of the handle and somehow soldering some jumpers or something in to make the switches do what you are wanting. I want to say there is an address to change in there somewhere but that would be too easy...
__________________
2013 2500 Crew/Long 6.7 68RFE NV273 stock until 2018
2011 Jeep CJ7 304/T18/D300. D44's F&R on 35x12.50's
|
|
|
04-17-2011, 03:03 PM
|
#9
|
Name: kalder
Title: Kevin Alder
Status: Not Here
Join Date: Oct 2006
Location: Kittitas Valley, WA
Member`s Gallery
Posts: 1,286
|
I'm gonna see if the Honeybee connector is active when the CAB module is programmed to the rotary platform. If it is I'm golden.
If not I'll have to get the dealership to buy a $500 hydro handle for me to rework the circuit board.
__________________
Kevin
03 3500
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 03:01 PM.
|