Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Shop Talk - Tool and Shop Discussion! Tool and Shop Discussion! |
09-07-2017, 06:59 PM
|
#1
|
Name: RonA
Title: Too Much Time
Status:
Here
Join Date: Feb 2008
Location: Liberal ground zero.
Member`s Gallery
Posts: 11,058
|
Welding positioners.
My M&K products unit quit on me for a second time so I bit the bullet and bought another(larger) unit. Place back east called All-fab. Larger unit with muck heavier grounding capability. Got about 10 years out of the M&K unit so if I can get at least that much out of the new one I'll be fine.
__________________
55 years of work and all I got was a T-shirt.
|
|
|
09-12-2017, 06:42 PM
|
#2
|
Name: RonA
Title: Too Much Time
Status:
Here
Join Date: Feb 2008
Location: Liberal ground zero.
Member`s Gallery
Posts: 11,058
|
Takes a bit of getting used to with it being so much taller, but it seems to work well.
__________________
55 years of work and all I got was a T-shirt.
|
|
|
09-13-2017, 08:16 AM
|
#3
|
Name: Red Sleeper
Title: Too Much Time
Status: Not Here
Join Date: Aug 2009
Location: Lone Star State
Member`s Gallery
Posts: 4,595
|
Welding positioners.
Slick looking positioner Ron.
Did this one come with a foot petal also?
__________________
Nick J
'14 Silverado LTZ 5.3 4wd
'05 Cummins QCSB 4wd 48re
'91 Cummins w350 5spd
Last edited by Red Sleeper; 09-13-2017 at 08:17 AM.
|
|
|
09-13-2017, 10:02 AM
|
#4
|
Name: RonA
Title: Too Much Time
Status:
Here
Join Date: Feb 2008
Location: Liberal ground zero.
Member`s Gallery
Posts: 11,058
|
Yes it did. Along with a 3 jaw chuck for larger parts.
__________________
55 years of work and all I got was a T-shirt.
|
|
|
09-13-2017, 10:39 AM
|
#5
|
Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Detroit, MI
Member`s Gallery
Posts: 4,154
|
Quote:
Originally Posted by Red Sleeper
Slick looking positioner Ron.
Did this one come with a foot petal also?
|
Quote:
Originally Posted by RonA
Yes it did. Along with a 3 jaw chuck for larger parts.
|
Very nice. Was the drywall extra
Sweet setup Ron!
__________________
Corey - BSME '21 Tesla Model 3 Perf
'22 DMax AT4 2500
|
|
|
09-13-2017, 10:44 AM
|
#6
|
Name: RonA
Title: Too Much Time
Status:
Here
Join Date: Feb 2008
Location: Liberal ground zero.
Member`s Gallery
Posts: 11,058
|
I thought about moving my fancy splatter shield before taking the picture. I had it, I used it.
__________________
55 years of work and all I got was a T-shirt.
|
|
|
10-04-2017, 03:32 PM
|
#7
|
Name: thinair
Title: Not Enough time
Status: Not Here
Join Date: Sep 2017
Location: BC Canada
Member`s Gallery
Posts: 148
|
Look up L J Welding & Machine. We have a 12P-900 and has been flawless
__________________
94 12v. NV4500 Valair twin disc, Seth stage 4, DDP 5x14, 024 dv. Fass 260. T4 ATS. 362sxe. 150 ii springs.
2012 3500 CCSB. Thuren 2.5 kings, DT Profab radius arms. Carli LT Airbags/Sway Bar
|
|
|
10-04-2017, 08:31 PM
|
#8
|
Name: QMFB
Title: Fastest Welder in Texas
Status: Not Here
Join Date: Apr 2016
Location: Corpus Christi, TX.
Member`s Gallery
Posts: 1,061
|
I use a RTJ ring welded to a piece of 1-1/2" pipe, greased up and slid into a piece of 2" pipe. Weld a flange bolt across the 2" with nuts on each side welded down to the table. One nut welded to the front of the 2" with a bolt run to the table to ajust pitch...
Works like a charm, and it's free !
But then, I'm a cheap SOB.
__________________
04 CCLB DRW - 6.4 Cummins, HPTuners, 80% S&S, 10mm S&S CP3, AD165, s464 /s475, full billet 48re, Arp's EVERYWHERE, mild head work, lots of time and money... And never done.
|
|
|
10-07-2017, 10:24 AM
|
#9
|
Name: RonA
Title: Too Much Time
Status:
Here
Join Date: Feb 2008
Location: Liberal ground zero.
Member`s Gallery
Posts: 11,058
|
Quote:
Originally Posted by QMFB
I use a RTJ ring welded to a piece of 1-1/2" pipe, greased up and slid into a piece of 2" pipe. Weld a flange bolt across the 2" with nuts on each side welded down to the table. One nut welded to the front of the 2" with a bolt run to the table to ajust pitch...
Works like a charm, and it's free !
But then, I'm a cheap SOB.
|
Good enough for automotive work.
__________________
55 years of work and all I got was a T-shirt.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 10:10 PM.
|