Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
John Deere The Green machines |
02-16-2011, 06:45 PM
|
#1
|
Name: mikmaze
Title: Too Much Time
Status: Not Here
Join Date: Apr 2009
Location: Fairfield NJ
Member`s Gallery
Posts: 4,292
|
picking up a new to me JD 1070
Kind of excited, going tomorrow to get the tractor I been looking for........ For the usage I need it should be pretty good, I intend to brush hog and plow/ disc with it to make feed plots for hunting. This tractor was babied at a golfcourse for 20 years of its life, it is a 1991. Specs say she is a 38.5 hp 4 cyl diesel, non turbo. First time I went to look at it I did not warn the owner I was coming, I got there and it was 20 degrees out, tractor burried in snow. Firt thing noticed is not a drip of anything on the week old snow under it, and when the guy got there with the keys it fired right up. I know I should leave well enough alone, but are there any simple, reliable mods to get a tad more out of it ?
__________________
04.5 Qcab shorty EVIL TWIN CP3's 100 % over nozzles, ats 3 piece, HTT 64 71 13 ss over S480, arp's , GOEREND , Hamilton 181 210 & valve springs, UDC beta
2006 Liberty CRD w/ GDE eco
'91 JD 1070 dzl
|
|
|
02-16-2011, 06:54 PM
|
#2
|
Name: not enoughsmoke
Title: floatin in tha gulf
Status: Not Here
Join Date: Dec 2008
Location: tenn
Member`s Gallery
Posts: 5,730
|
They are great machines, but i would advise leave it stock they are high compression engines.
__________________
1995 F350 Powerstroke
1995 F350 Fummins
1995 F250 lightning clone
1968 Fastback GT
2003 F150
1994 F350 IDIT
1988 F350 IDIT
2003 Dodge 2500
1999 F250 Powerstroke
1993 F250 Fummins
1979 F350
|
|
|
02-23-2011, 08:41 PM
|
#3
|
Name: mikmaze
Title: Too Much Time
Status: Not Here
Join Date: Apr 2009
Location: Fairfield NJ
Member`s Gallery
Posts: 4,292
|
well had a chance to burn some fuel through it last week, fired it up and did a bit of brush hoggin, cleared a half acre field of 6 ft tall weeds and a few taller bushes/ small trees. Ran great, after an good long full pto rpm run parked it and no drips runs or leaks whatsoever. Happy about that, might have to look into why the pto wants to pop out of gear now and then. I did learn that it has a dual clutch, part way in and the wheel drive disengages but pto keeps running, all the way to the floor and both disengage. Currently looking for a 2 bottom plow with cutter wheel and depth gauge, or a 3 bottom that I can set the depth gauge a bit on the shallow side so as to still be able to pull it. Going to be a fun spring.
__________________
04.5 Qcab shorty EVIL TWIN CP3's 100 % over nozzles, ats 3 piece, HTT 64 71 13 ss over S480, arp's , GOEREND , Hamilton 181 210 & valve springs, UDC beta
2006 Liberty CRD w/ GDE eco
'91 JD 1070 dzl
|
|
|
04-13-2011, 09:32 PM
|
#4
|
Name: bosshogg
Title: Running with the best...
Status: Not Here
Join Date: Nov 2009
Location: Franklin, OH
Member`s Gallery
Posts: 510
|
That on will struggle with a two bottom, dont even think about 3!!
__________________
2013 2500 Crew/Long 6.7 68RFE NV273 stock until 2018
2011 Jeep CJ7 304/T18/D300. D44's F&R on 35x12.50's
|
|
|
04-14-2011, 06:42 AM
|
#5
|
Name: mikmaze
Title: Too Much Time
Status: Not Here
Join Date: Apr 2009
Location: Fairfield NJ
Member`s Gallery
Posts: 4,292
|
Its doing a lot better than i thought pulling the disc i have. I adjusted the angle for a better bite on the front cutting set and still rips along
__________________
04.5 Qcab shorty EVIL TWIN CP3's 100 % over nozzles, ats 3 piece, HTT 64 71 13 ss over S480, arp's , GOEREND , Hamilton 181 210 & valve springs, UDC beta
2006 Liberty CRD w/ GDE eco
'91 JD 1070 dzl
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 02:01 AM.
|