Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Dodge Competition and Performance General Dodge Competition and Performance Discussion |
02-01-2019, 06:36 AM
|
#21
|
Name: iride813
Title: Too Much Time
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 392
|
Is that a manual willwood master cylinder? Been looking into doing something with mine. If it is do you happen to remeber which one you used and how hard it was like any adapters or anything.
Sent from my iPhone using Tapatalk
|
|
|
02-01-2019, 06:45 AM
|
#22
|
Name: iride813
Title: Too Much Time
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 392
|
Also. Did you make those upper a arms?
Sent from my iPhone using Tapatalk
|
|
|
02-01-2019, 09:03 AM
|
#23
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by iride813
Is that a manual willwood master cylinder? Been looking into doing something with mine. If it is do you happen to remeber which one you used and how hard it was like any adapters or anything.
Sent from my iPhone using Tapatalk
|
Yes wilwood part # 261-13270. I removed and re-did the entire stock firewall, in part because I had to move my pedals 3.5" to the left because I had interference with inj pump and accelerator pedal. You might have to patch your firewall and add new holes for it. I haven't driven the truck yet, but if braking is very difficult I will adjust the pedal ratio. I shortened and used the stock rod from the pedal to the piston.
|
|
|
02-01-2019, 09:04 AM
|
#24
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by iride813
Also. Did you make those upper a arms?
Sent from my iPhone using Tapatalk
|
No, entire front end suspension, subframe and steering is from a 2004 ram 1500 2wd.
|
|
|
02-01-2019, 09:12 AM
|
#25
|
Name: iride813
Title: Too Much Time
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 392
|
Quote:
Originally Posted by Vincejax
Yes wilwood part # 261-13270. I removed and re-did the entire stock firewall, in part because I had to move my pedals 3.5" to the left because I had interference with inj pump and accelerator pedal. You might have to patch your firewall and add new holes for it. I haven't driven the truck yet, but if braking is very difficult I will adjust the pedal ratio. I shortened and used the stock rod from the pedal to the piston.
|
Alright man thanks. I rigged up the stock one to run as manual. I haven’t tested it yet. I feel like it’s gonna be a bit to aggressive but will have to see.
Sent from my iPhone using Tapatalk
|
|
|
02-01-2019, 11:17 AM
|
#26
|
Name: jasonc
Title: Too Much Time
Status: Not Here
Join Date: Nov 2009
Member`s Gallery
Posts: 4,412
|
I could steer it lock to lock sitting still on concrete with his big temporary front tires on it. I'm sure the engine setback weight had alot to do with that, but still impressed with the rack steering setup.
No power steering needed.
|
|
|
02-01-2019, 11:48 AM
|
#27
|
Name: RacinDuallie
Title: Black Sheep Racing
Status: Not Here
Join Date: Apr 2006
Location: Supporting Northeast Diesel Racing
Member`s Gallery
Posts: 17,369
|
That engine set back is phucking sick!
__________________
|
|
|
02-04-2019, 07:35 PM
|
#28
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by RacinDuallie
That engine set back is phucking sick!
|
Everyone acknowledges these trucks have a weight problem when it comes to racing...but they have an even bigger weight distribution problem. I'm not sure exactly what to expect, but I am hoping for much improved 60' and better handling and traction the whole way down the track. At full weight before any reduction my scsb truck had 75%F/25%R weight distribution. Before the engine setback I had it to 66%F/33%R. The goal now is I can move fuel cell/battery around and get close to a 50/50 or whatever works out best.
|
|
|
02-05-2019, 09:30 PM
|
#29
|
Name: RacinDuallie
Title: Black Sheep Racing
Status: Not Here
Join Date: Apr 2006
Location: Supporting Northeast Diesel Racing
Member`s Gallery
Posts: 17,369
|
Did you gut the bed?
__________________
|
|
|
02-05-2019, 09:50 PM
|
#30
|
Name: RacinDuallie
Title: Black Sheep Racing
Status: Not Here
Join Date: Apr 2006
Location: Supporting Northeast Diesel Racing
Member`s Gallery
Posts: 17,369
|
and you can still shed some weight with a hole saw if you are not building a tubular front core support .......
__________________
|
|
|
02-06-2019, 06:24 AM
|
#31
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by RacinDuallie
and you can still shed some weight with a hole saw if you are not building a tubular front core support .......
|
Definitely a lot more weight that can be cut. Still has steel rims, drum brakes, full bed, could remove rear crossmembers and put chromoly tube instead. I also still have a big trailer hitch on it!
|
|
|
02-09-2019, 07:52 PM
|
#32
|
Name: RacinDuallie
Title: Black Sheep Racing
Status: Not Here
Join Date: Apr 2006
Location: Supporting Northeast Diesel Racing
Member`s Gallery
Posts: 17,369
|
Quote:
Originally Posted by Vincejax
Definitely a lot more weight that can be cut. Still has steel rims, drum brakes, full bed, could remove rear crossmembers and put chromoly tube instead. I also still have a big trailer hitch on it!
|
mine has a hitch too. Although she's quite a bit larger.
__________________
|
|
|
02-19-2019, 10:47 AM
|
#33
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Update: Went and did my ring seat/finished engine break in on a loaded dyno. 5 pulls at 370cc of fuel and 28* timing. Engine spun quick up to 5100 rpm on the final run, stopped around 4500-4600 on the first 4 pulls. I noticed looking at the datalogger that my airdog 165 got pulled down to 14psi by 4000rpm, so a change there is in order. I'm a bit disappointed that the airdog couldnt even support ~640hp without losing most of it's pressure. Also of note is my stock engine on this same fuel setting made ~550hp, pretty good gain from the pistons/cam/head porting. Bunch of odds and ends to tie up. Excited to start track testing soon.
|
|
|
02-20-2019, 09:58 AM
|
#34
|
Name: iride813
Title: Too Much Time
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 392
|
Quote:
Originally Posted by Vincejax
Update: Went and did my ring seat/finished engine break in on a loaded dyno. 5 pulls at 370cc of fuel and 28* timing. Engine spun quick up to 5100 rpm on the final run, stopped around 4500-4600 on the first 4 pulls. I noticed looking at the datalogger that my airdog 165 got pulled down to 14psi by 4000rpm, so a change there is in order. I'm a bit disappointed that the airdog couldnt even support ~640hp without losing most of it's pressure. Also of note is my stock engine on this same fuel setting made ~550hp, pretty good gain from the pistons/cam/head porting. Bunch of odds and ends to tie up. Excited to start track testing soon.
|
Dang I figured for sure a 165 should be capable of 750 Atleast. I was gonna run dual 150 pumps but I’m considering trying out power drivens new belt driven deal. I’m hoping to start testing with mine aswell soon.
Sent from my iPhone using Tapatalk
|
|
|
02-20-2019, 10:07 AM
|
#35
|
Name: iride813
Title: Too Much Time
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 392
|
Quote:
Originally Posted by Vincejax
Update: Went and did my ring seat/finished engine break in on a loaded dyno. 5 pulls at 370cc of fuel and 28* timing. Engine spun quick up to 5100 rpm on the final run, stopped around 4500-4600 on the first 4 pulls. I noticed looking at the datalogger that my airdog 165 got pulled down to 14psi by 4000rpm, so a change there is in order. I'm a bit disappointed that the airdog couldnt even support ~640hp without losing most of it's pressure. Also of note is my stock engine on this same fuel setting made ~550hp, pretty good gain from the pistons/cam/head porting. Bunch of odds and ends to tie up. Excited to start track testing soon.
|
Also. You don’t think that 62 you have is limiting you do you? Most with the fuel you have I see are 66-69 paired with the 88
Sent from my iPhone using Tapatalk
|
|
|
02-20-2019, 10:35 AM
|
#36
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by iride813
Also. You don’t think that 62 you have is limiting you do you? Most with the fuel you have I see are 66-69 paired with the 88
Sent from my iPhone using Tapatalk
|
I'm sure it will be a limiting factor eventually, but probably will be limited by the T3 manifold and .7 housing on the manifold turbo first.
|
|
|
02-20-2019, 10:37 AM
|
#37
|
Name: Vincejax
Title: Too Much Time
Status: Not Here
Join Date: Apr 2018
Member`s Gallery
Posts: 327
|
Quote:
Originally Posted by iride813
Dang I figured for sure a 165 should be capable of 750 Atleast. I was gonna run dual 150 pumps but I’m considering trying out power drivens new belt driven deal. I’m hoping to start testing with mine aswell soon.
Sent from my iPhone using Tapatalk
|
I'm sure it could support more hp, but not with good fuel pressure.
|
|
|
02-25-2019, 05:36 PM
|
#38
|
Name: Jeffrey Weeks
Title: Diesel Enthusiast
Status: Not Here
Join Date: Dec 2016
Location: Denver, NC
Member`s Gallery
Posts: 183
|
im excited to see how it will perform! it came a long way since the last time I seen it.
|
|
|
02-25-2019, 07:24 PM
|
#39
|
Name: jasonc
Title: Too Much Time
Status: Not Here
Join Date: Nov 2009
Member`s Gallery
Posts: 4,412
|
Quote:
Originally Posted by Jeffrey Weeks
im excited to see how it will perform! it came a long way since the last time I seen it.
|
It gotta a little out of hand, ha
|
|
|
02-25-2019, 07:25 PM
|
#40
|
Name: Jeffrey Weeks
Title: Diesel Enthusiast
Status: Not Here
Join Date: Dec 2016
Location: Denver, NC
Member`s Gallery
Posts: 183
|
What happened?
Sent from my iPhone using Tapatalk
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 09:56 PM.
|