| Advertisement |
|
|
|
|
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
08-22-2016, 11:00 PM
|
#1
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
Which speedo gear ?
I have 3.54s, 30" tires . I had 4.10s
__________________
stock 94
|
|
|
|
|
08-23-2016, 06:32 PM
|
#2
|
Name: GAmes
Title: Retired Apache pilot
Status: Not Here
Join Date: Jun 2012
Location: Killeen, TX
Member`s Gallery
Posts: 271
|
You need to have a start point. Use a GPS to find the true speed then compare it to the indicated speed. I'd use a round number, 50 or 60 mph to make the math a little simpler. If your true speed is 60 and the speedo shows 70 you need a gear with more teeth. How many more? 70 is 1.167 X 60. If your present gear has 30 teeth you need one with 35 teeth (1.167 X 30).
__________________
'97 Dodge 3500, G56, slightly bombed, A million+ miles, started 2nd million on 8/24/13 Now past 1.3 million and going strong.
|
|
|
|
|
08-24-2016, 01:54 AM
|
#3
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
I found some at Patc
__________________
stock 94
|
|
|
|
|
08-28-2016, 08:45 PM
|
#4
|
Name: odieub
Title: Too Much Time
Status: Not Here
Join Date: Nov 2007
Location: Leitchfield, KY
Member`s Gallery
Posts: 923
|
There's 2 oem gears that I know of. Green 3.54. Red 4.10. And I seen a black one other day it was sam diameter and number of teeth as green one.
__________________
95 1500 rc sb 2wd p7100 24v auto, ats 5 star, suncoast kit, dtt billit input, sperico, fun tire eater. In pieces
95 2500 2wd rclb nv5600 500k 5x.012 ddp 887 pump, #11 plate hx35/40-14cm
16 3500 4wd aisin cclb dually flatbed, toy hauler
|
|
|
|
|
08-29-2016, 02:47 AM
|
#5
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
Thanks
__________________
stock 94
|
|
|
|
|
08-29-2016, 09:31 AM
|
#7
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
Right on. I've been on night shift all summer and I keep forgetting to call the place from the those links
__________________
stock 94
|
|
|
|
|
08-29-2016, 10:05 AM
|
#8
|
Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Detroit, MI
Member`s Gallery
Posts: 4,154
|
You should reply back on if we need short or long shaft, just for future reference.
__________________
Corey - BSME '21 Tesla Model 3 Perf
'22 DMax AT4 2500
|
|
|
|
|
08-29-2016, 10:55 AM
|
#9
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
I'm waiting for a call back from Jim at PATC/ transmissioncenter.com
__________________
stock 94
|
|
|
|
|
08-29-2016, 11:11 AM
|
#10
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
Just got off the phone. I'm pretty sure he said I need a 30 tooth gear if my output gear on my t case has 13 teeth. Most of the 241 dhds do or it's an odd ball 7 tooth.
In most cases a t case with a speed sensor will have the short shaft/shank speedo gear
In most cases a t case with that has a cable driven speedo will be a long shaft/shank speedo gear
But not always. it's best to pop it out and take a look before I order. Also I need to figure out where to count the teeth in the t case. He is a busy guy
__________________
stock 94
|
|
|
|
|
08-29-2016, 11:13 AM
|
#11
|
Name: SCHMITTY
Title: Not enough time
Status: Not Here
Join Date: Jun 2012
Location: K beach, AK
Member`s Gallery
Posts: 1,183
|
It doesn't quite match up with the chart though.
__________________
stock 94
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 11:56 AM.
|
