1950 international L110 harvester - Competition Diesel.Com

1lowdiesel · 10-27-2009, 11:47 AM

like the title states i am selling my 50 L110. overall the truck is in very good shape. light surface rust w/ just some small spots that are rusted through.

i started the truck with the intentions of making it a diesel rat rod but used the motor for another project. the truck is apart and the stock frame and engine are long gone. i started to build frame rails for it out of dual 1.5" 3/16 dom w/ 1/4 gussets.

the grille is there just pretty dented up. the hood, roof, doors and cab floor are almost rust free. the fenders have some rot at the corners but in great shape overall.

i started to senction the bottom of the bed fenders so i could make them even with the cab but never finished,i still have the pieces though. the bed is very solid and only has a few small pin holes in it. also it is a SB w/ spare tire cut out.

i don't have the stock rear but do still have the stock front end. i do however have a 10 bolt disc brake rear out of an 01 chevy that will go with it.

doors still open and shut very easily. all glass still good except left rear window.

looking to get $650 obo and will consider trades.

more pics can be found here.

http://s64.photobucket.com/albums/h1...SEL/rat%20rod/

06 DIESEL · 10-27-2009, 12:36 PM

Man I wish I had somewhere that I could keep this and work on it. I have been wanting an old international for a long time. Here is a bump for ya.

1lowdiesel · 10-27-2009, 12:51 PM

thanks man, yea i wish you had the room too.

if you buy it i can store it in my place for a while till you find somewhere

therabbittree · 10-28-2009, 07:17 AM

where are you located?
Thanks
Deo

1lowdiesel · 11-04-2009, 02:58 PM

i'm in central jersey. but i can deliver it if needed. sorry for the late response.

therabbittree · 11-05-2009, 06:53 AM

mummn ..I'm in southern ny outside poughkeepsie..so nj isn't bad..I've been debating tearing my rotten first gen can off one of my truck chassis and putting a old truck cab on it..your truck body may fit the bill. can you give me a few measurements?.. outside cab width and widest part, the back of cab to the center of the front wheel well, length from back of cab to the front grille, oh and cab height... is all the glass decent?..
thanks
Deo

1lowdiesel · 11-05-2009, 09:55 AM

sure no problem. yea i was just up there a few weeks ago to pick up my new project.

i'll have to dig it out of the corner tonight and measure that stuff up.

the glass is all good with the exception of one glass that has an inside crack in it, the windows still work perfectly though. i do know of a local yard that has a few of these with that piece of glass in perfect shape.

WILD_PHIL · 11-27-2009, 03:26 AM

Man I wish you didnt live on the other side of the country. I have the same dang truck just missing the bed, but mine runs and drives. All I need is what you have but I paid 1k for the whole truck so it wasnt a bad deal.

shawnsack · 12-19-2009, 03:34 PM

would the frame be included? any drivetrain besides axles?

BlueOx03 · 01-01-2010, 04:53 PM

Damn Kyle, I was looking forward to seeing this thing done. If I lived closer I would pick it up and put a PSD I have in it...

1lowdiesel · 01-08-2010, 09:46 AM

Quote:

Originally Posted by shawnsack

would the frame be included? any drivetrain besides axles?

well the only frame i have now is the one i started to build. and sorry no motor or trans.

Quote:

Originally Posted by BlueOx03

Damn Kyle, I was looking forward to seeing this thing done. If I lived closer I would pick it up and put a PSD I have in it...

yea i'd like to keep it but i just don't have the time for it and it's taking up valuable shop space. i have my K20, the dmax, my chummins project and my Plymouth so...

ha that PS would be right at home in there. road trip

1lowdiesel · 01-27-2010, 01:07 PM

ttt....

it wants to get out soo bad

]

1lowdiesel · 02-18-2010, 12:38 PM

no longer for sale... putting it on a 95 dodge chassis w/ a 12v

cumminspuller · 02-18-2010, 01:02 PM

Quote:

Originally Posted by 1lowdiesel

no longer for sale... putting it on a 95 dodge chassis w/ a 12v

Be sure and post pics!

1lowdiesel · 02-18-2010, 01:24 PM

of course! i'm going to pick the truck up monday.

1lowdiesel · 05-14-2010, 10:29 PM

truck back up for sale...

10-27-2009, 11:47 AM	#1
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	1950 international L110 harvester like the title states i am selling my 50 L110. overall the truck is in very good shape. light surface rust w/ just some small spots that are rusted through. i started the truck with the intentions of making it a diesel rat rod but used the motor for another project. the truck is apart and the stock frame and engine are long gone. i started to build frame rails for it out of dual 1.5" 3/16 dom w/ 1/4 gussets. the grille is there just pretty dented up. the hood, roof, doors and cab floor are almost rust free. the fenders have some rot at the corners but in great shape overall. i started to senction the bottom of the bed fenders so i could make them even with the cab but never finished,i still have the pieces though. the bed is very solid and only has a few small pin holes in it. also it is a SB w/ spare tire cut out. i don't have the stock rear but do still have the stock front end. i do however have a 10 bolt disc brake rear out of an 01 chevy that will go with it. doors still open and shut very easily. all glass still good except left rear window. looking to get $650 obo and will consider trades. more pics can be found here. http://s64.photobucket.com/albums/h1...SEL/rat%20rod/ __________________ 05 LLY PPE hot, boost controller, 4" t-back 6" custom black stack, airaid / AEM intake, air ride parallel 4 link. 99 RCSB Chevy 2wd cummins bagged and bodydropped Thank you sponsors:XDP, Pureflow,McGaughys, DJM,

10-27-2009, 12:36 PM	#2
06 DIESEL Name: 06 DIESEL Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Location: Kingsville, MD Member`s Gallery Posts: 1,565	Man I wish I had somewhere that I could keep this and work on it. I have been wanting an old international for a long time. Here is a bump for ya. __________________ My rig - 06 Dodge Ram 2500 Crew Long 4x4 SLT CTD 6 speed A little here, a little there... Sled pulling video's can be found here

10-28-2009, 07:17 AM	#4
therabbittree Name: therabbittree Title: Diesel Enthusiast Status: Not Here Join Date: Nov 2007 Location: LaGrangeville, NY Member`s Gallery Posts: 145	where are you located? Thanks Deo __________________ 2000 Excursion XLT 4x4, P Pump 12V, G56 6 spd, SB FE clutch, guages, hx50/ht3b twins, dana 60, exbrake http://www.turbodieselregister.com/f...sion-redo.html http://picasaweb.google.com/therabbittree/Excursion02#

11-27-2009, 03:26 AM	#8
WILD_PHIL Name: WILD_PHIL Title: BLACK SMOKE DIESEL CLUB Status: Not Here Join Date: Nov 2009 Location: Texas Member`s Gallery Posts: 74	Man I wish you didnt live on the other side of the country. I have the same dang truck just missing the bed, but mine runs and drives. All I need is what you have but I paid 1k for the whole truck so it wasnt a bad deal. __________________ 05 F250 4X4 TUNED, DELETED, MODDED, ADDED, LIFTED 92 SINGLE CAB CUMMINS 2WD 5PEED PROJECT DRAG TRUCK 86 CHEVY CREW CAB 4 SPEED 454CI PROJECT CUMMINS CONVERSION MUD TRUCK BLACK SMOKE DIESEL CLUB (Black smoke diesel club) \| MySpace - myspace.com/blacksmokedieselclub FACEBOOK BlackSmoke DieselClub

01-01-2010, 04:53 PM	#10
BlueOx03 Name: BlueOx03 Title: Green Behind the Ears Status: Not Here Join Date: May 2006 Location: Down in Mississippi and up to no good... Member`s Gallery Posts: 67	Damn Kyle, I was looking forward to seeing this thing done. If I lived closer I would pick it up and put a PSD I have in it... __________________ 2004 GMC 2500 LB7/Allison SCIV/AutoTrac/Quadrasteer Tuned to be smoooooth and strong with Moonshine by Tony @ Ridgerunner Diesel Performance. Many one off mods by me.... If you fear dieing....then you're already dead!

10-27-2009, 12:51 PM	#3
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	thanks man, yea i wish you had the room too. if you buy it i can store it in my place for a while till you find somewhere

11-04-2009, 02:58 PM	#5
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	i'm in central jersey. but i can deliver it if needed. sorry for the late response.

11-05-2009, 06:53 AM	#6
therabbittree Name: therabbittree Title: Diesel Enthusiast Status: Not Here Join Date: Nov 2007 Location: LaGrangeville, NY Member`s Gallery Posts: 145	mummn ..I'm in southern ny outside poughkeepsie..so nj isn't bad..I've been debating tearing my rotten first gen can off one of my truck chassis and putting a old truck cab on it..your truck body may fit the bill. can you give me a few measurements?.. outside cab width and widest part, the back of cab to the center of the front wheel well, length from back of cab to the front grille, oh and cab height... is all the glass decent?.. thanks Deo

11-05-2009, 09:55 AM	#7
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	sure no problem. yea i was just up there a few weeks ago to pick up my new project. i'll have to dig it out of the corner tonight and measure that stuff up. the glass is all good with the exception of one glass that has an inside crack in it, the windows still work perfectly though. i do know of a local yard that has a few of these with that piece of glass in perfect shape.

12-19-2009, 03:34 PM	#9
shawnsack Name: shawnsack Title: Green Behind the Ears Status: Not Here Join Date: Dec 2009 Member`s Gallery Posts: 46	would the frame be included? any drivetrain besides axles?

01-27-2010, 01:07 PM	#12
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	ttt.... it wants to get out soo bad ]

02-18-2010, 12:38 PM	#13
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	no longer for sale... putting it on a 95 dodge chassis w/ a 12v

02-18-2010, 01:24 PM	#15
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	of course! i'm going to pick the truck up monday.

05-14-2010, 10:29 PM	#16
1lowdiesel Name: 1lowdiesel Title: Diesel Pro Status: Not Here Join Date: Sep 2007 Member`s Gallery Posts: 685	truck back up for sale...

Advertisement

Want to advertise?