Recent content by BigHemi02

Have a complete 98 harness and ecm. Thought it had a bad 5v as I lost alternator and tach. Bought a whole nother 98 truck. Taking harness off I see one of the alternator tabs is gone, otherwise in good shape. Was from a manual and doesn't have the grid heater set up. Selling as unsure about...

Have the AutoMeter monster tach with recall. Set up for cummins, the 6k RPM one. Parted out race truck no longer need. Runs off the balancer bolts. I have a bar that mounts the pick up so no fab work required bolt.on and go. Works with a big compition balancer too. 400 plus the ride, should...

I just got done swapping my motor and a 6 speed into a new 98 3500. Motor was my old 'race' motor. Pulled it from the drag truck and swapped the 5x.022s to 5x014s, Turbo went from an sx475 to a s366 silver bullet 3rd gen. Went into a 98 qcsb with a built 47rh and was really fun to drive, no real...

Tach bounces over 2500 rpm. Took off the autometer 5" tach and going to a stock look. Swapped from a comp fluidamper to standard. Autometer tach was ran off the 4 bolts in the damper and worked flawless. New factory tach is off the damper and set at .50 tho works under 2500, then starts...

Bringing motor back down to street. All parts have been sitting in my shop for a few years, pics available upon request through email or text. Willing to trade. Competition Fluidampr (no belt) $300 Jegs Electric water pump $100 Steed Speed Manifold, angled Port, T6 non wastegate style $500...

75/96 1.15 T6 SX4 Turbo, with blanket. has about a dozen runs, like new, powder coated red front cover. - $1000 Shipped Steed Speed Comp manifold, Angled, Non Gated, T6 - $800 Shipped 5x.022 Injectors, contagious, IIRC, have a few dozen runs - $800 Shipped Fluid Damper Comp Balancer, NON...

1996 Reg cab short bed 2500 truck cut down hx40 over s472 fire ringed, ARP studs, 60lb springs 5x.14s, 12mm pump from dynomite, full cuts, 4ks all gaskets replaced and truck is leak free powder coated engine bay in white and blue, MANY new parts batts relocated under rear of bed triple disk...

NOT STREET LEGAL fully gutted sport conversion 2500 cut and plated to a VERY straight and firm shortbed aluminum dash with guages (pyro, boost, drive, volt, oil, water, trans, fuel) lowered 4" on nitto 420s over moto 970s maxed pump with .120 DVs and lazer cuts with 5ks 188/220 cam, HD CHromoly...

Synapse 50mm wastegate. NIB P/N WG002B.1 Has the factory spring, and also bought the Additional springs, E,F,G, iirc. Also NIB. Non diaphram wastegate. Does not have clamps, the box is opened and i dont remember where they went. Can buy them for a few bucks. Retail was $460. Ill sell it for...

Lookin for a steed speed t6, 12v, with wastegate Lookin for t6 1.15 96 housing Have cash, or t6 header manifold

Bought it, sold truck. 2 boxes, never opened. B and W turnover with ball and everything. 450 shipped. Paypal or local cash. Or TRADE. Need a t6 1.15 divided 96, steed speed manifold, shortbed tonneau cover, or any 2nd gen 12v go fast parts or race truck stuff. West Palm Beach

the ppump 24v is in, has a dodge 47rh. motor harness is basically done. issues i have is how to hook up the cam signal? i have the crank on the front with the DCS kit, right now cam plug goes no where, and i dont have an adapter plate with the fancy cam adapter destroked sells. also, PATS is...

Looking to see whos got efficient charging setups for in between runs. I dont run an alternator, 2 new optima yellow tops. I have a battery tender for weekly charging, but i need something to keep the truck cooked for 3-4 runs in a night. Currently have to hook jumper cables to my tow pig (new...

Where can i find a 6.4 engine wiring diagram. Need one ASAP, and every link that pops up is a dead link. TIA

External waste gate, NIB, box opened and beat but never used, has flange and spring BOV, NIB, box opened and beat but never used, has flange $140 shipped