Recent content by cfunk

  1. C

    13mm Ag Governor P7100 Pump

    I have a 13mm P7100 pump without a timing gear for sale. Was built by Diesel Injection Service and checked out last season (about 20 passes since then). 960cc max setting. $2800, call or text 920-988-1326.
  2. C

    11.5 AAM Billet Aluminum Rearend Girdle

    I have a billet aluminum rearend girdle for 11.5 AAM rear ends. It has a 1.5" thick aluminum girdle plate that is O-ringed and doweled to the rearend housing. It uses spacers between the bearing caps and girdle plate and includes long bolts to tie the girdle, spacers, and caps together. Also...
  3. C

    14mm 12 Valve Head Studs

    I have a set of used 14mm head studs for a 12 valve. They are standard length studs from Haisley Machine. $500 OBO 920-988-1326
  4. C

    Vailair Triple Disk Pulling Clutch

    I have a Valair triple with about 10 runs on the disks and floaters in it so should be good to go for a while yet. Comes with the bearing and carrier but will need the heavy duty cylinder kit to operate it. Call or text 920-988-1326 $1100
  5. C

    Profab NV4500, Transfer case, Driveshaft Parts

    I have an NV4500 trans with a Profab kit in it so it has three gears, 1:1, 1.04:1, and 1.08:1 for sale. It can come with a long 1.5" spline input shaft that will work with a 4 disk clutch on a Cummins or a Duramax or it can come with a 1.375" spline input shaft that will work with a 3 disk...
  6. C

    Carrillo Rods

    I have a set of standard length Carrillo rods for sale with one torque on a fresh set of bolts. $2100. Call or text 920-988-1326
  7. C

    Harts 5 x .025 billet body dual feed injectors for sale

    For a 12 valve, $1500. 920-988-1326
  8. C

    2.6 Pulling Truck Parts For Sale

    I have the parts below for sale: 1. Hart's 2.6 HX60 turbo with about 12 passes on it. $2200 2. DHD spool, axles, drive plates, and billet bolt covers for a GM 11.5 SRW AAM rearend housing for $1800 3. A custom billet AAM 11.5 rearend girdle that ties the main caps to the girdle plate. The...
  9. C

    Hart's 2.6 PPL compressor wheel and cover

    I have a Hart's HX60 2.6 PPL compressor wheel and cover for sale in good shape for $1200. Will include an air shutoff made to fit the cover for another $200. Call or text 920-988-1326
  10. C

    12 Valve 5x.022 injectors

    I have a set of 6 Cummins 12 valve injectors for sale that are dual feed with 5 x .022 tips. The spray pattern is a FVP pattern that was setup for factory pistons with the marine style bowls. There is 0 run time on these since they have been cleaned, inspected, and pressures set. Asking $850 for...
  11. C

    5x.022 12 Valve Injectors

    I have a set of 5 x .022 12 valve dual feed injectors. Have not been run since they were cleaned, checked, and pressures set this week. PM, text, or call me for other details. $1000 920-988-1326
  12. C

    Heat Treated Rods, Kenny's Girdle, Billet Tappet Cover

    I have the following items for sale: Heat treated and balanced rods purchased through Cummins Performance Parts. $700 Scheid billet tappet cover that has never been used. $225 Kenny's 12 valve girdle with 14mm studs. $750 920-988-1326
  13. C

    2001 2wd Allison Transmission and TCM

    Truck ran and drove fine before the trans was pulled, I was told the tranny was rebuilt approximately 30, 000 miles ago by the previous owner but have no proof of that. Comes with TCM and converter. Located in southern WI. $700
  14. C

    WTB 6.7 block

    Looking for a 6.7 block in the midwest area.
  15. C

    gm 9.25 aam front diff left axle

    I am looking for the left front differential axle for a 2001 gm 2500 or 3500. Please pm me a price if you have one. Thanks.
See more
Back
Top