Recent content by DISTURBED

Anyone ever swapped 32 spline axles out of an 01 into a 30 spline housing? What did you do at the cad? The 32 spline axles won't go through the cad, so did you bore out the housing or turn the axle down

So I bought an 06 with a blown engine. Burnt number 6 piston. Every other cylinder looked perfect. Built a new engine and sold the truck to a guy. Long story short he was in a hurry for me to finish it and wouldn't wait for Bosch injectors so he ran in town and bought a set of BWD injectors from...

Looking for a good 06 Dodge Cummins ECM for an Automatic truck. Anybody have one laying around?

I have a fresh 04.5-07 CR long block. New .020 over Mahle pistons, Clevite main and rod bearings, head was completely redone with valve job. I installed it in a truck and the owner is going a different direction. You can hear it run before i pull it back out. 0 miles. Its only been ran to pull...

Richard was involved in a car wreck and passed away. RIP https://m.facebook.com/story.php?story_fbid=890712974470890&id=386694201539439

I just found out a little bit ago that Billy Deblasio was in very bad accident on Oct 4 while working on the pipeline in WV. Billy ran the XDP Dodge for many years with east coast and Full Pull Productions. If you are looking for a pull next weekend here's one you should attend...

They can be seen cleaning up something on the truck just before the run. Don't know if that had anything to do with the crash or not. https://m.facebook.com/story.php?story_fbid=2082864295070901&id=172048049485878

Has anyone found a place to get the trans cooler pipe that goes from the lower radiator hose around the back of the block and into the trans cooler, aftermarket? The cheapest I've found online is $700 for the 2 pieces of pipe and a hose that's a foot long.

Anyone have any Arias STD bore pistons laying around. I have a set of 5 and looking for 1 that's a close match. I figure this is a long shot. Valve relief on the intake in the .250-.260 range, .215 on the exhaust and 11.8 cr

Who has pulled and replaced the crank gears? I tried to get my machine shop to do it and they said there is a "special" process to pulling them off and putting them back on. Something like has to be heated the entire time it's pulled and replaced. I'd never heard of it but they won't do it.

Fresh built 04.5 engine on start up sometime will build pressure on the gauge then drop to 0 and the check gauge light comes on. Shut the truck off and restart immediately and it builds pressure again. Normally 30-40 seconds after start up it does it but not every time. I put a mechanical gauge...

So long story short I have a Engine here that spun #1 rod bearing but also started to spin #2 & #3 only slightly. I've inspected the Engine and can't find anything wrong with it. Mains look brand new and so does 4-6 rods. The oil is very sticky like it has a some stabilizer additives in it...

Any one here ever had a aluminum driveshaft through the weights off? I slammed on the brakes the other night to miss a deer and developed a vibration afterwards. Found a u-joint that was going bad so I replaced both joint's and the vibration is still there. So started looking closer and you can...

So I moved my old 2.6 truck the other day out from in front of the combine so I could get it out for harvest. It's been moved for a few weeks maybe a month. Me and my boy were messing around in the bay where the truck was setting and he said he found a bolt in the gravel, so I told him to let me...

So I have this 07.5 that I've been fight a rail pressure code issue. I have changed almost every thing in the fuel system for different parts and it still sets the low rail pressure and low lift pump codes daily. Something I have noticed was when the truck had the original 400k mile parts on it...