Recent content by foreman9984

12v 7mm Harts dual feed billet injectors, fresh from check over and reset, comes with install kit $1800 Intellidash data logger - works great just went with bigger system. Shows voltage, tach RPM, 1 pressure (boost), and 1 EGT. Comes with everything to hook up and use including new magnets for...

Used E.D. billet turbo air guillotine. Good shape, works as intended. I used an adapter boot to mount to turbo so it can be adapted to fit many sizes. Uses 2 cables for kill but will work with just one if that's all that's required $350 call or txt 8I5-499-6620

I ordered this temp sensor kit fot a Cat C7 engine in a Ford F750 because the website said it was the correct applicatuon but it was not. My loss your gain as I will never use it so instead of it sitting in my shop collecting dust make me an offer on it and you can have it. Located in NE Iowa...

I have stock axle shafts, stock cover, welded carrier without gear all best offer if you need them. Used posi-lock for Dana 60 comes with locking cable, axle cover, fork, switch, breather fitting $100 plus shipping Synergy steering kit for 94-99 with a Rancho RS5000 steering stabilizer. It...

Nice set of rear molded mud flaps came off a 2005 I just bought. Couldn't use them with fender flares. Have the ram logo on the back side, both sides in good shape and includes some hardware. Call or text 815-499-6620 for pics. $30 obo plus shipping

I have a good set of 4.10 gears from Dana 60 & 80 both in very good shape. The Dana 60 spool is 30 spline for factory axle shafts not sure what gear size it is meant for. $150 for each for gear set and spool. Call or text 815-499-6620 for pics.

These parts are in good used condition, plus shipping, if my prices are high please make me an offer, need to clean up shop. Call or text 815-499-6620 for pics and more info. Thanks, Lee. *12v core head, needs cleaned up, all still assembled $125 picked up in eastern Iowa or you cover shipping...

I have most of a p-pump 12v engine parts (no pump or injection lines or block) for sale. I also have 90% of a ve 12v engine. If you need anything for either engine let me know. I have both heads, ve lines, cams shafts and gears, retainers, 5 sets of rockers, valve covers, a good new Cummins...

Looking for a dual axle assembly preferably with leaf springs attached in good shape that will fit 2004 3500. Seller would also have to ship it to IL or IA to make it work unless your close to the Mississippi. I'm not sure on the gear ratio of this one but will figure that out this week. Let me...

I bought these from a guy here on compD and was told they would work as standard studs but I believe they will only work with an SMT roller rocker setup. The 14 mid length studs are about 7/8" longer than a standard 12v head stud. This set is complete and has been torqued twice. $850 for the...

This turbo has 11 hooks on it, always cooled afterwards, runs good, minimal shaft play, no marks on housings, has the small .9 exhaust housing so may be a good candidate for 2.5" automatic transmission pulling truck. $1500 shipped was $2500 new Here's a link to the specs. Engineered Diesel...

Tearing down my pulling truck for changes to a new class, selling a weight bracket, made of 2x2 tubing and 1/2" plate with rollers under it. I had 1000 pounds on it worked great $200. Selling a fuel tank from ext. cab Ram 2500-3500 with factory sending unit, straps, fuel neck, lockable or...

All parts listed for 12V. I ended up with too many parts and need to make some space. Call or TXT 8I5-499-662O for more info and pics please. ARP 425's have one torque and 5 hooks but are missing 6 washers, I'll let you figure out why. They can be bought from ARP I'm sure. $300 plus the ride...

I have a 2002 F350 crew cab short bed pulling project I bought but may be switching gears to a different truck. I bought it just as it sits except added front tow hook. It has been pulled before and comes with Cummins motor mounts, NV4500 trans, Dana 80 rear axle with dual wheels and tires...

I am posting this for a customer of mine, he doesn't want to put anymore money into this truck because he has two others that are similar. It is a 2007 5.9 CCSB auto (needs rebuilt) cloth interior, 4x4, has rust on front and rear fenders. It had a new evaporator housing, new a/c compressor, has...