Recent content by swamp_ratt

Looking for some insight. Had to tear down my motor due to low compression in one cylinder that ended up being a broken ring. As it was, it's a p-pump 24v around 650hp. I use it to daily drive and tow heavy probably 10 times a year. What are everyone's thoughts on gapless rings in this...

For those of you that have swapped a Spicer or Eaton, what are you doing to operate your clutch? I'd like to retain the hydraulics from my truck rather than retrofitting mechanical linkage. Also does anyone have a part # for an sae2 flywheel housing for a 6bt with the starter on the intake side...

Tearing down my lbz to do a build on it and selling some of the stock parts. Right now I have... Stock pistons and rods in excellent shape, motor had LOW miles Stock cam Stock intake plenums Stock valve springs Stock pushrods Stock y bridge Stock van style intake horn Stock downpipe Stock van...

Have an 85mm holset ht4c I'd like to part with. Asking $800 obo

Long story short, I was having #6 not firing in my p pump 24v. Plunger wasn't sticking and loosened the barrel and rotated it back and forth. Returned to original position and tightened down. Now as soon I even snug it down, it stops the rack from moving. Loosen it to finger tight and everything...

Have an lbz van motor for sale. Supposed to have around 130k miles. Was in a cab fire, tops of injectors and wiring are melted. Complete long block. Located Hudson WI (20 minutes east of Saint Paul MN! $2500 obo

Does anyone know where I can get solenoids for lbz injectors? I have a motor that was in a cab fire and it melted the tops of the injectors. I've been able to find lb7 solenoids, buy can't find any lbz. Thanks

I have a core turbo, cp3 and injectors off an lbz motor. Some of the injectors has the tops melted. The motor was in a truck that has a cab fire. Turbo and cp3 look to be fine, and doesn't appear to be body damage to injectors. Need all these gone!

Alright, some time ago when building my fuel system, I found some small -10 orb ball valves that spun right into filter base and had -10 an outlet for push-loc style fittings. They were on a diesel performance site and were like 20 bucks each. For the life of me, I can't find em again. I want to...

I have a set of core injectors, cp3 and turbo in a motor I just picked up. The motor was in a truck that had a cab fire and melted all the wiring and the tops of the injectors. I'm wanting to use these maybe as a partial trade to get good injectors and cp3 to get it running. I believe the motor...

Well, I'm swapping a p-pump 24v into my 97 that the 7.3 blew up in. I'm looking for part numbers for radiator hoses, power steering line to hydroboost and what wire coming from the idm relay to the idm is 12v supply power. None of the guys on the Ford forums are any help and won't even answer...

53 block, very clean, not cracked, needs to be bored $300 Crank, good shape $150 Cam with gear $100 Head, rusty under valve cover, needs work make offer Vp44 with lines $375 Core injectors and tubes $125 Complete 24v wiring system (ecm, pcm, and in cab. Pcm is 2 plug harness) not sure what it's...

Well, my 7.3 had 2 decent failures in under 2 months, this second one wiped it out. So, Saturday night, I acquired a 120k mile vp motor for some light horse trading. I was told on another forum to get ahold of roachie over here to get some help on the wiring as he's done a few! On my phone, for...

International Dt360 engine, swapped to 160hp p7100. Has cut delivery valves, 4k springs set about 4300, flows around 500cc, rack plug, and no fuel plate built by contagious diesel. 5x20 injectors by contagious diesel as well. Has ported head, valve job, cut valve guides for 160# springs, custom...

Got a ton of parts for sale. Make offer on all. Need it all gone. Obs rear springs no longer available! http://minneapolis.craigslist.org/wsh/pts/4751458563.html