Search results

I have been having some really odd shifting for a very long time and last night I plugged in a scan tool that would display the TPS reading that the PCM views. I had fixed a loose brake pedal which would cause the brake switch to act strange and fail, but I continued to have a torque converter...

Looking to see what your Map sensor reads on a stock 2002 VP truck if anyone has that information. -No boost foolers. -No tunes. -ECM reflashed to verify no unknown software. -New MAP sensor I have checked with multiple scanners and everything reads 55 inHg with truck not running. Current...

I am looking for a little guidance, and/or suggestions. The swap will happen between a 98.5 manual and a 2002 auto. So the 98.5 will be going Manual to Auto The 2002 will be going Auto to Manual. Both trucks need to be up and running afterwards. I have done a lot of reading on the subject and...

Does anyone have any experience with AG Diesel solutions performance module? https://www.agdieselsolutions.com/product/34000/ Not many options for the Mercedes out there.

13 Ram 3500 longhorn with MM3. Flashed a new tune in and now the rear turn signals do not work and it gives a “lamp out” message. Front, dash, and trailer signals work. Tried going back to the old file with no change. Brake lights do work. Has factory LED tail lights. Flashed with battery...

I have a 97 3500 that I cannot get the cruise control to work. I have followed all the troubleshooting in the factory manual. New clock spring and control switches. The little green light will light up (but you cannot turn the light off until you shut off the truck) Using a snap on scanner to...

Anybody else have death wobble issues with the new front end? If so, what corrected yours? I have a stock 13' 3500 Dually with stock size tires and no lift/leveling. The truck has 50,000 mi on it and it really likes to death wobble. It has recently been aligned twice and I installed a new track...

Can somebody please snap a picture of the 5 pin flat plug that plugs in to the dash side of the clock spring? It's just under the bottom cover that is held on by 3 torx screws. 94-96 seem to be different wire colors....I checked. Someone cut the connector off and disposed of it! Thank you!

Looking for at least 1 Dually center cap for a 97 Dodge 3500 front wheel. Thank you!

I am on a road trip and logged a P20EE on my stock 2013 RAM3500. In almost 70 gallons of Diesel I have not used any DEF. I am pulling an empty flatbed trailer. Does anybody know if there is a filter between the DEF tank and the doser nozzle? Or am I looking at possible pump or doser valve...

I have a 2003 that is in need of a rebuild. I stumbled across a complete 6.7 out of a 2008 for a good deal, cheaper than I can rebuild the 5.9. I have been doing a lot of reading on the swap and it seems the only way to go is to use the 03 injectors. I would really like to utilize the he351ve...

Does anybody have the measurements for their driveshaft on a regular cab short bed conversion 2WD truck? I would like to get a jump on getting a drive shaft made.

I have 6x 2003-2004 Common rail injector cores: $320 Shipped CP3 Core from 2003-2004: $150 Shipped 2 Sets of 24v Stock injectors: $100 EA set shipped (Would probably run but being sold as cores) Thanks!

I have a friend of mine that was wondering what would be a good setting for the smarty S 06 POD that would be safe to tow horse trailers at altitude (5000-7000). Truck has an exhaust and a cold air intake and a lift pump. It also has a really well-built transmission. Would like it to be not very...

Does anybody have the pressure to volts scaling for the 3 different MAP sensors on the vp trucks? I have a truck that I am trying to figure out. It is a 98.5 with a 2002 engine and ECM. But the engine wiring harness is a 98.5 so there is a 98.5 MAP sensor. Trying to figure out if the MAP needs...

This head is for a VP-44 24v, but it is already trimmed to use with a p-pump. All machine work was done at Mountain High Performance in Aurora, CO. Here is a list of what is done to the head: Resurfaced .010" All 24 Valve guides replaced with cryo treated Cummins guides Street performance...

I know this question has been visited before, but it seems as if it was not answered. What, if any, would be the difference in 12v to 24v VP rings? Could I use a set of 12v rings in my 24v VP build? I did some basic searching on quickserve but just found that they have a different part number...

I am looking for just the engine harness for a 2001. Please let me know if you have one for sale.

I have 2 of the Turbonetics 11117-BB turbos for sale. One is brand new in the box with the 1.00 A/R turbine housing $1400.00 Shipped The other has around 40k mi on it and will come with one .84 A/R turbine housing and one 1.00 A/R turbine housing. This turbo was on an Excursion that had a EDGE...

Is there any sort of install instructions for an older Iron Giant II clutch in to a NV5600 ? Just wondering if the release fork will need to be ground down, and if so where. Also if the pivot ball will need the washer removed or not. One more question: is the release fork for the NV4500 and...