Search results

Ats 3rd gen manifold T4 flange still has factory paint,ran less than 5k miles. $385 Call/text 540-578-3335

Just like Bd cover with the 90* built in,I'm planning on 850+ on a 05 6 speed cummins with hp tuners and the supporting mods. I'm gonna do a 2nd gen swap and wasn't sure on the difference between a regular Borg s467 billet and Bd s467 with there new 90* cover also I was thinking a .90 exhaust...

Just wanted some opinions to see if I was going in the right direction, truck has been well maintained almost has 200k miles though I'm kinda concerned with the higher miles?I was thinking the normal supporting mods valve springs,studs,pushrods,lift pump etc. with dual cp3s and 75% injectors or...

Is there any clearance problems running a straight 7/16 pushrod in a 12 valve?

Smarty pod 03-07 cummins TNT software, $475 Call or text 540-578-3335

I would like a laramie front bumper for 06 and up dodge, Would be a plus if it was mineral gray I think thats what its called but anyway the gray color. I have a Ranch hand style front bumper on my truck that I want to take off, Its a Frontier full replacement.

I have two dana 80 rear ends both of them are 3.55 geared, one is from a dually the other is for a single wheel. both have drum brakes $600 each Located in va

I have a 47re tranny came out of a 97 dodge 4x4, It has DTT converter, billet input shaft, upgraded to 48re valve body, mag hytech pan, billet servo/accumulator, billet piston, all new frictions, seals and front bushings. fully built by Tim Barber TRE Diesel. Tranny only has 6,500 miles but a...

I recently purchased the VW Jetta TDI he had listed on here. He had it listed with all the mods for the sale price of $5500 or best offer on here and he had it listed with the same mods for sale on TDI Club for $5000. I bought the car on Saturday and drove it till Tuesday and the turbo exploded...

97 3500 ex cab 5 speed 134k miles. The truck has several mods I will list what I can remember: 370 injectors, 4kgsk, 60lb intake and exhaust springs, #10 fuel plate, valet switch, AFE air intake, Jacobs exhaust brake,BD short throw shifter,rebuilt tranny within approx 15k miles,boost pyro...

I was running twins last year and switched to a II phat shaft 71 and I really like it. But I need to get my *nx* kit on because after I lock it in o/d it gets under the charger and starts surging. The track wasnt prepped that great my 60's were way off from last year 1.50s and 7.20ETs. The best...

avatar test

I have thought of putting new rod and main bearings in before this season starts, My truck has around 185k it sounds great im around 600hp now but will be higher shortly with some *nx*. I just need some suggestions Josh

Like the title says it wont show any of my sent pm's, I can see all of my inbox but no outbox?

This is a Piers kit wh1c over bht3b they have around 35,000 miles on them, the wh1c has a banks 14cm housing and big head wastegate actuator. The hot pipe has a divorced wastegate passage, all of the cold pipes are powder coated. comes with oil lines downpipe air filter etc. everything in the...

These are mild steel .093 lines $180

What are the pro's/con's of different thickness head gaskets? Its a friend of mines truck which is a daily driver. Its a 98 12V auto with O-Ringed head, HTT 71/74/14, DDP 4's, and 5K GSK. He is putting a new head on and was wondering what gasket thickness would be best. I run a .020" over but i...

Like the title says I need a good hy35 with a fair price for a project im working on.

I found a good deal on a (Turbonetics Y2K-88MM E-Trim Ball Bearing Turbo .http://www.turboneticsinc.com/products/index.php?products_id=922&category_id=8096 T6) and was wondering how it will work for a bottom and what size top turbo would I need?