Search results

Looking for a 4bt. I would like a complete engine can be in need of freshening. Only looking to go about 200 miles from my house in Orefield Pa. Thanks Mike

Looking for injectors for an LB7. Would like Prices on new and reman and the gasket kits to install them. Thanks

Anyone going? POWER HOUSE PULL 2012 - Kempton Country Fair

I live in eastern Pa outside Allentown. Looking for someone close to me to build my spare 47re. I have a couple good trans shops around me but they don't really get into building diesel transmisions outside of putting billet convertors in. When the truck goes back together it will most likely...

The block in my dually is cracked bad the crack goes the entire length of the block. I have to drive this thing a little while longer till my other engine is built. My question is has anyone made their own block strengthener plates like the ones lock-n-stitch sells? I think that may be a...

I am designing the logo for my shop. I would like to have a cartooned truck with stacks (preferably a Dodge) in the design but I can't find any in my searching. IF anyone has something could you please put it up here. Thanks Mike

Looking for a quote on 18mm gaskets and studs for a 6.0. Thanks, Mike

Anyone ever messed around with duece and a half's? I'm thinking about buying one to bob as an advertisement piece for my new shop. I tried a couple searches and could only find where people swapped turbos from other duece's and 5 ton trucks. I was thinking about running an S300 of some size...

I am rebuilding a 12V for my dump truck Dodge 3500. I use this thing for hauling (obviously) plowing and salting in winter. Most of the places I have found rebuild kits want to sell me pistons with a bigger bowl in them thus lowering compression. My question is with this truck only used for...

Does anyone know what turbos were on the old 855 cummins engines. A friend of mine used to have a few farm trucks with 855's in them and I remember the turbos used to have a nice whistle to them at idle especially the IH with the 290. I'd like to put that same turbo in a twin set up to see if...

I have an 03 that I am working on. The guy just replaced lift pump,CP3 with industrial injection 85% pump and replaced rail pressure sensor. The problem the truck has is when you start it the rail pressure is pretty high(always varys) and it is hard starting when hot. I hooked up my scan tool...

Just curious if it can be done I'm not a transmission guy but I am thinking about putting a lock-up trans in my 93. Just got a thought I might be able to use existing trans with different valve body and maybe some more holes machined out. Let me know your thoughts.

Anyone know a good source for step vans with 4bt's? I've been checking in my area but nothing really shows up.

I checked around and all I find is people talking about a 14mm head and diff. camplate for 4cyl ve's. Anyone know a part number or an application or anything. Thanks Mike

I am building a dodge cummins tough truck. The drivetrain is 97 Dodge 2500, the frame is cut down to have a wheel base between long and short bed reg cab. The 12 valve is stock internally it has 370 injectors. The pump is a 215 and will remain stock except for plate/afc mods and either 4k or...

I am interested in becoming a site sponsor in the near future. I would like to know what is involved and required to become a sponsor. Thanks Mike

Anyone know of a good shop in PA or close to Pa that can rebuild common rail injectors?

I have a 93 D250 extended cab. Its my daily driver right now but wont be soon. I have been thinking about puting full air ride on the truck. I don't need it to be a low rider by any means I want it for the ride. I did some searching and came up with about nothing for front brackets. Has...

Thought I'd throw this up here. Anyone goin? I'll be spectating damn trucks are broke. POWER HOUSE PULL 2011 - Kempton Country Fair

Anyone make a heim joint steering besides thuren fab.? Or did anyone fab their own? I'd like to make one up for my truck just seeing if anyone runs a heim set up on the street. If anyone made their own pics would be cool. Thanks Mike