Search results

Putting the truck back to stock and want to trade my carrier for a stock 3 series carrier for dana 80 to put back in cause the buyer is going to tow equipment trailer with it. Had a local drivetrain specialist weld up my carrier because I didn't want to shell out a bunch of money on a locker or...

Taking the truck back to stock to sell. I need to find a plug that goes in where the primary turbo oil drains into. It drains into the rear hole on side of block that late 12 valves and 24 valves have. Any ideas? Thanks

Got a set of Weston's 7x.012 injectors with. 015 lift and stroke. Took them out last year when I switched to 6x.016s. Putting truck back to stock now to sell. Apt. 3500 miles on these. As always, I recommend getting them cleaned and checked. $450 shipped to lower 48 or 400 shipped plus a...

Pros and cons of the PRW platinum flexplate? read that on a few trucks that after install of these flexplates, the pumps burnt up. Need to buy a new flexplate. Trashed my laminated plate. between a PRW and a billet one. Jesse B.

trashed my laminated flexplate. looking for a good billet or sfi replacement. Thanks, Jesse B.

Trying a new set of 6x.016s from E.D. These will be out this weekend. Got these from 00BlackRam back in April. They had about 2000 miles on them then. I have probably put 1000-1200 miles on them since they have been in my truck. These are rated at apx. 240hp. Looking to get $550 shipped...

Looking for deal on some 6x16 or 6x18 injectors. Just trying to see if anyone has some before I go buying a new set. Let me know what ya got. Jesse

Long story short, my truck hangs the 3-4 shift under WOT at the drag strip. Searched and there is no adjustment for this. Heard that i can run a switch to the OD solenoid and make it shift when I want it to. Question is how and what wires do I hook the switch to? Jesse

Going back to a single. These Twins consist of a Holset H1C with a 60mm GDS compressor housing and wheel with your choice of 12cm or 16cm exhaust housing; 12 is on it now. over a Borg Warner BHT3B w/ 26cm housing. Both chargers are used, but have minimal shaft play. I added an E.D. 50mm external...

I know its late notice. Got about 7 of us going so far. Thought I would throw an invite to anybody else who would like to come and race. $20 for test and tune at Muncie. Supposed to be a high of 61 and low of 42 and clear. Goes from 5:30pm to apx. 9:30pm. Hope to see you there. Jesse

Ben has a set of these and I want to know if they would be way too much for my setup and a SO pump. I havent found much info on this particular size injector. I clean these .015 lift and stroked 7x.012s up with ease right now, and after talking with Kyle the other day, I am leaning towards...

I have a set of Weston's 24V 7x.012s with .015 lift and stroke that I bought off of 00blackram about a month ago. They had 2000 miles when I bought them from him and I probably put 3-400 miles on them since. I need more injector. I clean these up with ease. They make good power, but after...

Went to the track last Wednesday and made some passes. I just think this combo should run a little better. One good thing is that I have a new best 60' time. I tried different tunes and levels on the Quad and the best I could do with a race weight of 6400 pounds was 60' 1.710 330' 5.126...

Truck is Defueling at WOT in 3rd gear when it gets ready to go into OD. It even pops up on the Pulse that it is DEFUELING. I have all of the defuel settings turned off. My Adrenaline still has the factory tune on it, and the only thing that I can think of is that is Defueling because of too many...

Found these on Youtube and I gotta say, I like the way this guy thinks. Not sure if these videos have been around before, but here they are. Its a case of "practice makes perfect".

Check the mods in my sig. This is a whole new setup from when I was at the track last time. Any possibility of cracking the 11 second zone with what I have. I know my twins setup is old school, but its what I have. I am trying to give the truck as much of a diet as I can. gonna try and get it to...

Got a 2000 qcsb 4x4. Its a street/strip truck. No sled pulling. Want to shed some more weight if possible. So, I am thinking take off tailgate and rear bumper and support, hitch is gone, take out rear seat and middle and passenger front seat. Maybe Get a Kirkey aluminum seat to throw in and...

I had some JL 7x.014s. Traded for these DDP 200's. I now want to go back a little bigger. I am wanting to trade these 200's for some DDP Comps or JL 7x.012s or something in that 240-250hp range. Let me know what you all got. Thanks, Jesse B.

my buddy is getting ready to buy a 2002 chevy ccsb d-max. he wants to see what some nice 20" wheels would look like on it. he is either gonna stay stock height or maybe a 4 inch lift. lets see what ya got. Thanks

[YouTube:zW4KO6Ca-S0]