Search results

Hey guys, my friend sold his truck and has some parts kicking around, if anyone is interested. On Craigslist... http://albany.craigslist.org/pts/5794000875.html http://albany.craigslist.org/pts/5794007589.html http://albany.craigslist.org/pts/5752251445.html

I was wondering about opinions on when it's really beneficial to decompress a CR motor. I have an 06 Cummins, ported head, and have had a few sets of twins on it. Makes around 900/1600 fuel limited, due to stock rods, still. When I did the head install, many years ago, I did a bit of research...

Hey guys, I'm looking to buy a clutch for a very lightly modded 07 5.9. Thinking a twin should be considered for holding power and pedal effort. Probably will be a South Bend, wondering about who to order it from. The truck isn't down, but it slips, so we're ready for a proper fix. Also, do they...

Looking to sell a GT35r that I bought used. Story is that it was on a 6.0l powerstroke and was removed to trade in. One of a set, as twins. Shaft is nice and tight, no issues. I have a open T4 .84 turbine housing and a divided T4 1.06 as well. Both turbine housings are brand new, as the turbo...

I'm just about ready to install my new turbo setup, so it's time for them to go. They are still on the truck, everything works perfectly, no issues at all, I'm just going bigger. Everything was purchased new, and have been on the truck about 4 years, and about 25,000 miles. The truck makes about...

I bought a Steed manifold directly from them and plans have grown so he is making me a different one. I have handled it and loosely installed it on the head only, but never run it at all. It is a t4 angled with the 50mm gate on the opposite side. Meaning if you bolt it on angled down, the gate...

I am looking at an 04.5 long block to do a new motor build for my 06 truck, and wondered if the 5.9 commonrail blocks are all the same?? I know about the pistons and injector differences, but is there a "preferred" block? I would be reusing my head, cam, turbos, etc.... Looking to go to the...

I have searched and read at least a dozen threads about this, and come up with a lot of inconsistency about how and why to use a resistor in the wiring. I would think the computer would not like to see the lockup wire disconnected at any time, therefore the resistor is needed, but where it has...

Finally got my twin pumps on and cranked up the tune, 898 hp and 1605 tq....very happy! Working on getting the video posted.....I won the "Rudy's Truck Jam" event at Piedmont Dragway Saturday, and not so much as a trophy was offered....?? Typical??

I have a Smarty and an mp8 for a 06 5.9, Smarty is loaded with tnt tunes, mp8 has never been plugged in, still in the box. I am thinking 450 for the smarty, and 250 for the mp8, shipped. The other Smarty is for a 08 6.7, with pod, I believe has Revo tunes in it. Set up for all emissions...

I have a strange misfire problem in my 06 and am looking for thoughts and suggestions. I noticed this at idle, in gear, a few months ago, and haven't really had time to do much about it. The truck has a sidedraft zz fab intake, ported head, a fletcher killer b cam, flux 3.4 injectors, twin...

OK guys, looking to buy a NEW cp3 and NEW injectors for a early 04 cummins. I have bought many parts from Shane at Wicked in the past but it seems he is no longer participating in this sport....I went to Floor It's website, no phone number listed, should I call industrial? Who can get me some...

I have a friend's 06 dmax dually in the shop, it is completely stock except for a bullydog programmer. No intake or exhaust, stock. It came in yesterday, complains of excessive black smoke, reduced mileage, slight lack of power. I found the air filter plugged, the filter minder in the red, and a...

I bought a set of CR injectors from a member on here, and the bodies (according to Don M) are junk. I bought them as flux 3.5's and supposedly had 40,000 miles on them, before having the nozzles changed. Since then, they were supposed to have 500 miles, pulling and dyno time only. I didn't ever...

Does anyone know how to contact Don M? I tried to PM but his inbox is full, no phone number on his site ( or E-mail) , Dealers for his products are too busy to answer the phone, what do I do? I bought a set of his injectors and would like to get them cleaned and checked out before I install...

Has anyone used the PCS trans controller? I looked on their website and they don't support the 48re directly, but Suncoast sells it with a harness and valve body, pre-programmed, any thoughts or opinions? I called Dave at Goerend's several days ago, no return call yet, and I haven't spoken with...

I thought I'd share my findings after installing a sidedraft intake from ZZ Fab along with my (non professional) porting job and bowl work. With no other parts or tuning changes, my boost is down substansially; I could previously make 50 PSI with little effort, letting off to save the stock...

I just spent an hour searching and came up empty; wondering what your opinions are on a universal air filter for my twins should be. I am currently running a K&N and noticed some oily residue and super fine dust(???) in the turbo inlet. Becoming more interested in a dry filter, what brand, and...

I would like to manually shift my convertor clutch when beating the truck hard. What I think I would like to do is shift the truck through all 4 gears, in tow haul mode for more line pressure and a firmer shift, but delay the convertor until a higher RPM or vehicle speed. The problem is the...

I installed my new ported head with ZZ fab intake on my 06 cummins a few weeks ago, and was wondering about gasket crush. Upon inital installation, I torqued the head up to 150 ft. lbs. in 25 lb. increments, then loosened each one, one at a time, re-lubed head, washer, and threads, and retorqued...