Search results

did they stop using the saddle jet plugs on the 13+ 6.7 blocks and only have provisions for the j-jet now Sent from my SM-G991U using Tapatalk

looking for t6 non gated 24v manifold Sent from my SM-G991U using Tapatalk

like title says lookin for a set of wide bowl stock bore 6.7 pistons Sent from my SM-G991U using Tapatalk

looking for set of qsb 6.7 pistons New or anywhere that may have them in stock Sent from my SM-G991U using Tapatalk

have a new 63/68 /12 drop in sxe ,, was idled around yard never driven on road and was taken off for a fleece cheetah vgt I won in a raffle 1000 shipped Sent from my SM-G991U using Tapatalk

t6 1.25 housing ball bearing gt47 with custom 11 blade turbine. 7 passes since new ,located in iowa will ship , 2500 obo Sent from my SM-G991U using Tapatalk

I have a ported 24v cr head that I just tore down. after tear down and cleaning up I have pretty noticeable cracks across exhaust ports. this head is getting tore down to be hard blocked and new big valves and seats going in for a deckplated 3.0 motor. with this being a dry block and...

looking for any 6.7 solid blocks that may still be sitting around, thanks Sent from my SM-G991U using Tapatalk

drop in sxe 63mm for. 3rd gen cummins , fmw ,360 thrust bearing. 12cm wastagted t3 housing ,, was mounted on truck drove back and forth from shed to shop a few times then taken off not even 20 mins run time and only idle time ,, $1150 SHIPPED Sent from my SM-G960U using Tapatalk

Looking for a used dropbox and reverser. No 1 inch boxes ,willing pay shipping Sent from my SM-G960U using Tapatalk

Like title says looking for a hamilton solid 6.7 block Sent from my SM-G960U using Tapatalk

48re , all goerends parts , billet input ,intermediate, output. Constant pressure full manual valve body with most current updates. Triple disk converter, 12 blade high stall. 2800 rpm or so, spooled a good sized 3.0sb very nicely. Has billet anchor ,strut and band , pistons and...

04 block wet block , 360 degree thrust bearing 14mm main studs with gorilla girdle and line bore deck was machined flat and setup to run MLS gasket 207/220 Hamilton steel cam with full cam bearings and new lifters at time of instal .020 over cast mahle pistons , .100 fly cuts...

,, just wondered. What most think is the effective life span of a set of maxspool dual valve springs is , I have a set I used on the street for 50k or so and now in a 3.0 truck seeing 4500+ rpm Sent from my SM-G960U using Tapatalk

06 rail pressure stuck at 27,535 all the time truck running or not ,, multiple display sources through obd2 . Change rail sensor , fca, and a blown. Relief . Still the same, rail sensor pigtail has 4.5 volts and ground . Any ideas ? Sent from my SM-G960U using Tapatalk

3.0 smooth bore charger,, ball bearing s400 , 87/1.25 t6, one season on it,, no shaft play . from midwest turbo/CRT $1500 shipped from Iowa Sent from my SM-G960U using Tapatalk

S400 based ball bearing biller wheeled 3.0 smooth bore. 87 turbine with a 1.25 t6 housing.vband outlet , 15 passes. Built by midwest turbo/ CRT $2000 shipped Sent from my SM-G960U using Tapatalk

Looking at putting motor this winter on a dyno and wondered what way guys feel is best way to go about wiring for a common rail ,, 07 ECM and harness. But what are you doing for the truck side and keeping everything happy. Most available dynos around here are running mechanical stuff...

Have factory borg 467 fmw , part number 178923 has a small chip in wheel edge and few nicks , bearings are tight. $450 shipped or located in northeast Iowa , can send more pics Sent from my SM-G960U using Tapatalk

Have a manual tune on my full manual vb truck and would like to log trans output shaft speed , does anyone know the pin out on those sensors as in power ,ground or how they work, I have the pid loaded in v2 and shows up while logging but no output. I know some of the stuff is turned...