Search results

I installed a new set of tophat seals on my truck and ran them for about 17k before i had to tear the engine down, when i tore it down i noticed the metal part of the tophat had broke off on a bunch of my seals. After looking at it more, there is a small shoulder that goes around the guide. This...

I have a bunch of 2nd gen parts leftover from trucks I've parted out, interior stuff, wire harnesses, computers, clusters, VP gears, etc. If you need something just ask, tons of stuff not pictured I parted out one 2001,and two 2002's. Will trade for 24v performance parts

This pcm came with a ppump swap I bought, wanted to sell this thing but wanted to figure out what year truck it's off of first.

Ppump 24v with 260k on it, suspected something was up as I started losing a Quart of oil in 400 miles when towing 6,000 ibs. At idle the truck shows very little blowby and passes the oil cap test no problem. Compression test on a cold motor at 60 degrees f shows 425,425,410,408,325,425. Did a...

Went to check the rear end in my fummins as I'm going over the truck for a upcomming trip, and find my magnet covered in metal material. So I pull that cover and the only thing I find is it looks like the steel plate from my limited slip is eating into the diff. Wondering what you guys think...

Builds are never completed, atleast for me as I'm never happy and always changing things. But I figured I'd try to add some diesel content to this place and maybe help somebody out who's thinking about the same swap. Im far from an expert, but do all my own work with the capabilities I have...

Mainly I just want to cover boost, egt, and trans temp. Looks like the reviews on the new cts3 are bad. Wanting something that's clean looking in my 08 Ford.

Looking for billet input, output, along with C2 hub. Also looking for a v2, does not need a Vin license as I'm only using it to tune the trans. Thanks guys

As the title states I'm looking for a billet p2 planet for a 2006 allison, used or new. Also in the market for a billet input if the price is right. Thanks guys

Just finishing up a rebuild on a zf6 out of an 08 and am trying to figure out what the specs for the bearing preload for the main and counter shaft should be. The book has an equation to figure out Shim size but no spec for actual bearing preload. No gears or shafts were replaced and everything...

Is it possible? I pulled the vanes out of my vac pump since it's not needed on my fummins build. I was hoping I could not run oil to it to eliminate another possibility for an oil leak and also more simplicity since I'm using the existing oil line for my ppump since it's a p24v Sent from my...

So I get home from a spirited drive to the parts store last night, go to back into the garage and I have no reverse. I figure something screwy with the low/reverse band as I haven't adjusted it since I built the trans(26k ago) so I dropped the pan today and double checked it and it was fine and...

I have a buddy that picked up a tandem axle kenworth with the 3406c. He has complained since day one that it is low on power compared to his general tandem axle with the big cam Cummins. I'm not well versed in these trucks at all and haven't worked on them much at all other than doing a clutch...

So ever since I converted my truck over from a fmvb to a regular auto vb(2016) I've been chasing this TPS problem. Here's the issue,when at idle I can watch the TPS number on both my edge,and anteater pro jump sporadically like this 0,10,0,15,0,0,0,0,12,0. When driving,average pedal position is...

Picked up a 08 6.4 with 189k on it. Has a rod knock over 1k rpms once it warms up. Passed compression test and injector balance test with flying colors. Motor is also studded and deleted. Trying to get a ballpark on what i can get out of this thing so I can start on the fummins build:Cheer:

So this will be the 2nd time I have blown the cooler supply line hose out of the fitting and hopefully the last time. The first time I was 1/2 mile from home so no big deal, this time I was 120 miles from home with a trailer. I'm using -8 stainless braided hose with summit fittings and it keeps...

So I installed a sump on my friends truck along with a fass 150. Anytime his tank is below 1/2 the sump starts sucking air when coming to a stop sign etc. I installed the same exact sump on my truck and I don't have this issue until I get down under 1/4 tank. The only differance is his truck is...

As the title states, looking to borrow a smarty to enable the high idle on my truck. Figured maybe I'd get lucky and find somebody close, I know diesel auto power rents them but I don't really wanna fork out 600 bucks in a rental

As the title states I'm looking at putting a pan heater on my trans this year. My low stall converter along with 6x13s don't really care for the cold under the 20s and I'm hoping this might make it a little more tolerable. Something that's 110v as I have a plug in at work also, I've seen the...

These have less than a thousand miles on them, fueled hard and were great with my 62/475 compounds. Only selling because I'm going ppump and need some money for 6 holes. Paid 575 plus cores, I'll take 500 shipped obo. Call or text 419-631-7991 Sent from my SM-N910V using Tapatalk