Search results

Selling the SFI rated Valair triple disc clutch kit ,complete with upgraded hydraulics, this clutch was in our landspeed racing truck, no sled pulling or drag racing in excellent condition. $1600 shipped

Just a quick update on our land speed racing escapades ,the Salty Box Racing 2008 Dodge truck managed 204.6 mph on the Bonneville Salt Flats this week, a new personal best plus it qualified us for the record. Unfortunately after the run we found that the motor was hurt so no backup run to seal...

Having some issues with an 06 ECM (CM849B) on the race truck, the tune going onto the ECM has the anti-theft stuff turned off, but when the ECM is tuned and we attempt to start the truck it does the start for 3 seconds then quit, giving us 5 attempts before it locks us out. Reload the tune and...

These are the injectors out of the land speed truck. We are putting in some bigger ones for this season. very few miles, dyno time and a dozen runs down the salt and a handful of runs at El Mirage. $1800 shipped, no cores required.

Looking for a dually rear axle from either 09, 2010 or 2011 model year to do a dually conversion on my 2010 3500 tow truck. Let me know if ya have one available. Thanks Tim

Looking to trade a 48re 4x4 tailhousing and output shaft for a 2wd 48re tailhousiing. Let me know if ya have one. Thanks Tim

I'm looking for a 48re 2 wheel drive tailhousing / overdrive housing for our land speed truck. If someone needs the 4wd stuff for a conversion I have the 4x4 parts. Thanks Tim

I'm looking for a dually rear axle for my 2010 3500,needs to be 3.73 ratio,will consider other ratios if the price is right. Will trade my SRW axle straight across if your in or near Colorado. Thanks Tim

I'm looking for a Gen 4 dually rearend with 3.73 gears to buy, or I have a Gen 4 single rear wheel axle to trade across,I'm in Colorado but would travel to surrounding states. PM me with details Thanks Tim

I'm looking for a 48re 2WD tailhousing and output shaft for a project I'm collecting parts for. My 1956 Cadillac coupe de ville is going cummins CR powered. I have a 48re 4X4 output shaft and tailhousing to trade if someone is doing a swap,or I'll just buy the shaft and housing outright. PM me...

I'm looking for an 03 -09 2wd Dodge quad cab long bed frame can be 1 ton or 3/4 ton with engine mounts for the cummins. Must be straight, no bent or tweaked frames. Preferably in Colorado or nearby. Let me know what you have Thanks Tim

For Sale:Industrial injection 'race' compounds for 6.7 or could be used 5.9 common rail 3rd Gen. Complete setup as it comes from II Silver 66 S480 All pipework downpipe oil supply line oil drain brackets Air filter assembly (S&B setup) I'll also include the BD gen 3 manifold. Used on our...

Selling off some spares so I can hopefully buy a set of billet rods for the fresh 6.7 race motor. 03-04fuel rail with sender and valve $250 I have 2 of these. 2 Good running CP3 pumps $350 each injector lines $80/set 1 set of reman'd injectors 20k on them $800 1 set of oem injectors, runners but...

All parts are from a cummins 6.7 ISB diesel engine,manufactured in 2007. Except for the set of connecting rods none of these parts will fit a Dodge application. All parts are from a cummins 6.7 with a rear mounted gear train system. This engine only had 54,000 miles on it. Engine was mounted in...

2004 Dodge Ram 3500, quad cab, short bed, 4x4,white,dark grey cloth interior,198K on the truck,the original motor dropped a valve, so I fitted a 2007 5.9 out of a totalled truck with 120k on it and 20k on a set of fresh injectors. Interior is clean driver seat has the usual holes on the outside...

I've decided to go with billet rods in the 6.7 race motor,so I'm selling the prepped up 12V rods that were in it. These are Brazil forgings,small ends and beams were polished then shotpeened,big ends resized,new bushings in the small end,arp2000 rod bolts fitted,the rods are weight matched ,I...

Well we were supposed to run it at speedweek in August and missed that,so now we are refocused on World finals.The thrash is on ....AGAIN! The truck is a 2008 Ram 2500 2wd with the 6.7 and a 6 speed.It was a salvage truck (hit an Elk) Here's what we started with. After we fixed it up a wee...

For sale:Dodge ram transfer case 273 D , it's the servo controlled transfer case (control knob on the dash) it came out of a 2004.5 1 ton 3500 dodge ram and was bolted to the back of an automatic.It has only 2800 miles on it,truck it came from was rolled when it was 4 wks old. $600 Located in...

I've been messing with cummins diesels for a few years now,mainly 4x4 stuff and cummins swaps.Currently building up a 2008 Dodge 2500 2wd with the 6.7 to run up at Bonneville salt flats in B/DT.I'll post some pics as I progress with the build.Meanwhile I'll keep taking notes from the forum.:bow...