Search results

Auto, 140,000 miles, ex gas company steel flat bed, good rubber, snow plow. Cab is rusty, needs drivers floor patched,not a cream puff cosmetically,but runs good. $4000 OBO,cash.

Brought to you by Haisley Machine. June 21st Muncie Dragway, June 22nd pulls, Gaston Lions Club park. DieselMotorsports.us

Brought to you by the Little Power Shop. July 20th, same place its always been. DieselMotorsports.us

2.5’’ The 2.5 street legal class is designed for daily-driven, on the road pickup trucks (full-bodied diesel pickup trucks). Valid DOT registration and license plates are mandatory. The vehicle may be two or four-wheel drive. Designation: 2.5” followed by competition number Weight breaks: 8000...

National Association Of Diesel Motorsports . 2.6 Street Diesel Designation: 2.6 Weight: 8000 lbs. Maximum, with driver. REGULATIONS: Ballast: Ballast is permitted. Hanging weights may not extend more than 60 inches from the centerline of the front axle. Batteries: Batteries must be...

Dads birthday. Hes had a lot of them. So the next time he tells you to get in your truck and pull ahead, keep your number where it can be seen, drop that hitch 1/4", don't go back to the pits after you weighed in, and any other numerous things you guys should know by now, cut him a break, hes...

All right hood stack boys and girls, you spoke, I listened, here is your chance. We are legalizing Hood Stacks for 2.6 class, one event only. September 17th, Buckeye Diesel Blast II, National Trails Raceway. You show me the numbers, and hood stacks will be legal next year in 2.6. We'll do a...

Basically anything in the cab with boost pressure, aside from a gauge,is probably a bad idea, I'm thinking. Thoughts, experiences?

NADM is back in Beloit! 3.0Trucks are welcome to pull SS. 07-09-2011 Bunker Hill Shootout 2.6 Class Goshen Community Center 15110 Middletown Rd Beloit, OH 44609, Sled Pulling 2.6/SS National and Ohio 2.6 Regional Points 1/2 mile East of State Route 534, 5 miles south of Rte 224...

Next year.... what do you guys think about dropping 3.0 and Work Stock, and dividing the 2.6 into Pro and Street Legal?

Hook 3A: Sertoma Truck Pull 06-11-2011 Crawford County Fairgrounds Meadville, PA 2.6 Nat and Ohio 2.6 Regional Points Co-sanctioned with Full Pull Productions FPP: Schedule... Run What Ya Brung 4x4 Street Semi Trucks-Pennsylvania Posse Pro Street GAS4x4 Start 6:00 pm Hook3B: We have another in...

Interesting. http://www.youtube.com/watch?v=xQhEOBfJsWo

Or evilness... could be either way. Jeff sent me some parts that arrived 26 hours from the time of the order, (OUTSTANDING!)as I opened it up, some nasty Tasty Kakes tumbled out. Does everyone get those with their order, or just the Tasty Kake Haters?:lolly:

http://www.southernmotorsports.net/ This is a good winter pull to start the New Year. Jan 7th and 8th. NADM will be supporting the event as usual with a vendor booth. Might go a day early and visit Lynchburg.:snoop:

Looking for able bodied men and women who want to work like dogs, dawn to dusk on no sleep after you drove all night, with no glory and a ridiculously small amount of money to compensate your efforts. Here is a short list of jobs we do at events. Tech- the most thankless job in motor sports...

3.0 and Super Street Diesel The 3.0 (3.0) and Super Street (SS) classes are designed for full-bodied pulling trucks. The vehicle may be two or four-wheel drive. Designations: 3.0 or SS Weight: 8000 lbs. Maximum with driver. REGULATIONS: Ballast: Ballast is permitted. Hanging weights may...

Aside from SFI spec changes, these are the rules. Work Stock The Work Stock (WS) class is designed for daily-driven, on the road pickup trucks (full-bodied diesel pickup trucks). Valid DOT registration and license plates are mandatory. The vehicle may be two or four-wheel drive...

And a cracked 53 block. The 53 engine, head, crank, rods pistons have 250,000 miles on them. We took another engine and were going to swap heads, but after hot tanking and magnafluixng, found 16 cracked valve seats, plus the usual minor cracks. Found another head cheaper than I could put valve...

Is it possible to twist a cam like an axle and throw your engine out of time?

Nice article on the Ingram team, the attention is well deserved, you will be hard pressed to find a more dedicated pulling team/family. I flip through the Diesel mags on the shelf, if I don't know somebody, or if there is no article on sled pulling, the mag gets left on the shelf. Congrats...