Bleedin green
New member
- Joined
- Aug 21, 2011
- Messages
- 13
Im new as i said and im wanting to get into pulling, Ive been around truck pullers for quite awhile and have some friends that pull but im wanting to start out in hot farm (like tractors better). I am young 18, but i make good money as a welder and have money put back already. Ive read a little and heard alot about the 1066 case ih being a good starter but havent heard much on good john deeres to get started with. Anybody recommend a few good john deeres to start with? And also these are the rules for the pulling sanction i would be puling with.
A. This class is intended for farm stock tractors only!!
1. 1. No Super Farm tractors allowed.
2. 2. No Pro Stock tractors allowed.
3. 3. No Super Stock tractors allowed.
B. RPM limit is 3000.
Each tractor is required to have an Isspro magnetic pick up device
#019R8906. This is available at Schied Diesel, 1800-669-1593, for
approximately $51.00.
C. Tire Size
Tire size is limited to 24.5x32 or 20.8x42 or smaller.
NO CUT TIRES ALLOWED.
D. Air Supply Shutoff
Tractors must have an air supply shutoff in front of turbo workable from a kill cable at rear of tractor located 48” above drawbar, off 6”to either side.
E. Stabilizer Bars
Tractors must have stabilizer bars (wheelie). Bars must extend a minimum of 32” from center of rear wheel back. Bars must have a pad of 5” square minimum. Bars must have 20” minimum between the pads. Stabilizer bars must be able to support the weight of the tractor in the heaviest class pulled in. There must be a brace that extends vertically 12” from the rear most tip of the skid pad, and there must be a brace that extends inward to the frame, axle, or top of stabilizer bar arms.
F. Safety Tie Bars
Tractors must have safety tie bars mounted to the rear axe housing with at least 4 axle housing bolts and extending forward of flywheel area and fastened to side of block or main frame with at least 2 5/8 bolts. Tie bars must be of sufficient strength to support weight of tractor with the bolts used to split the tractor at the clutch bell housing removal.
G. Safety Blanket
Safety blanket must be on tractor bell housing.
H. Fly Wheel
Steel flywheel and clutch components are strongly recommended, but not required with 3000 RPM limitation and other safety equipment.
I. Roll Cage
Tractors are required to have roll-over protection capable to withstand the weight of the tractor in the heaviest class pulled in. Seat belts are required.
J. Drawbar
Tractors will have a drawbar maximum 20” vertical from ground. Drawbar must be minimum of 18” horizontal length from center of rear wheels back. Drawbars must have a hole for the hitch, oblong shape, 3¾” x 3” wide.
No clevis allowed!
A. This class is intended for farm stock tractors only!!
1. 1. No Super Farm tractors allowed.
2. 2. No Pro Stock tractors allowed.
3. 3. No Super Stock tractors allowed.
B. RPM limit is 3000.
Each tractor is required to have an Isspro magnetic pick up device
#019R8906. This is available at Schied Diesel, 1800-669-1593, for
approximately $51.00.
C. Tire Size
Tire size is limited to 24.5x32 or 20.8x42 or smaller.
NO CUT TIRES ALLOWED.
D. Air Supply Shutoff
Tractors must have an air supply shutoff in front of turbo workable from a kill cable at rear of tractor located 48” above drawbar, off 6”to either side.
E. Stabilizer Bars
Tractors must have stabilizer bars (wheelie). Bars must extend a minimum of 32” from center of rear wheel back. Bars must have a pad of 5” square minimum. Bars must have 20” minimum between the pads. Stabilizer bars must be able to support the weight of the tractor in the heaviest class pulled in. There must be a brace that extends vertically 12” from the rear most tip of the skid pad, and there must be a brace that extends inward to the frame, axle, or top of stabilizer bar arms.
F. Safety Tie Bars
Tractors must have safety tie bars mounted to the rear axe housing with at least 4 axle housing bolts and extending forward of flywheel area and fastened to side of block or main frame with at least 2 5/8 bolts. Tie bars must be of sufficient strength to support weight of tractor with the bolts used to split the tractor at the clutch bell housing removal.
G. Safety Blanket
Safety blanket must be on tractor bell housing.
H. Fly Wheel
Steel flywheel and clutch components are strongly recommended, but not required with 3000 RPM limitation and other safety equipment.
I. Roll Cage
Tractors are required to have roll-over protection capable to withstand the weight of the tractor in the heaviest class pulled in. Seat belts are required.
J. Drawbar
Tractors will have a drawbar maximum 20” vertical from ground. Drawbar must be minimum of 18” horizontal length from center of rear wheels back. Drawbars must have a hole for the hitch, oblong shape, 3¾” x 3” wide.
No clevis allowed!