dodgesledpuller
ColoPilot
28 Channel Data Logger
I bought this unit brand new and had it on my sled puller
for a little less than 4 months. This unit is nearly brand new.
$1200
(Pro Software Included)
-WIRELESS ADAPTER TO LAPTOP.
-3 RPM CHANNELS, Engine, Clutch, Driveline or Wheel Speed
-1 ACCELEROMETER CHANNEL, Forward G Meter
-12 ANALOG CHANNELS, Pressures, temps, position, Lateral G Meter, etc.
-8 EGT CHANNELS, Exhaust Gas temps, 0 -- 2400 DegF
-3 DIGITAL CHANNELS, WOT, N2O Stages, etc.
-1 BATTERY VOLTAGE CHANNEL (Internal)
-Dimensions: 2 Modules, 5" x 4" x 1" each
-INCLUDES ALL LEADS, 8 PYROs, and SENSORS.
I have a used Front Axle ARB Air Locker that was in my 06 Dodge 2500. Used twice. Comes with Air Compressor and Rocker Switches. $1000 for the whole setup or an offer I can't refuse.
Also have a rear spool. Same situation. The spool came from Randy's Ring and Pinion. $600 or an offer I can't refuse.
Water injection system from Scheid. Used it for one season on the puller. System is complete with water pump, 7 gallon water tank, injection nozzles, Simpson boost valve, all high pressure lines, manifold, fan pulley, love-joy coupling, on/off indicator light and mounting bracket for CR block. This will work with any diesel, you will just have to fab a mount for the pump if your application is other than CR Cummins. $1200 or your offer.
Compound Turbo Setup with hood stack (used). Complete kit with all parts ready to install. Comes with two TurboSmart wastegates. It is currently setup to run one on the small charger. Small charger is BorgW 66mm. Large charger is 92mm. You can see the setup in the above pictures. I can send more specific if necessary. $4500
Fully Billet Suncoast Auto Transmission with 3D Converter. Billet Input, Intermediate, Output, Front Drum and Piston, Acc Piston, Gov Piston, Rev. Piston. Currently has a fully manual valve body with OD and Lockup in every gear. We can switch out the VB if needed. $4000
105lpm Stainless Steel Injectors from I.I. fully balanced. $2500
CR Cyl Head fully ported with a beautiful valve job. Special valve seats, inconel valves, dual springs, ZZ side mount intake. I had this head mounted on a 6.7 block. Just had it checked and have paperwork for it. Will separate springs. $4000 for the whole thing.
6.7 Block 4.25 bore concrete filled with crank and main studs. Coated bearings. $2500 for the whole thing.
Also have a set of Ross Racing Pistons and rods to go along with it.
$1000
Truxxs Pulling Tires, Excellent Shape
33x12.5R18 (4)
$800
I have 2 on dually rims.
$500
I have the complete setup to turn your single wheel into a dually while keeping your stock rims on the outside to match.
$400
Bolt on weight box. Bolts into the tow hooks location.
$500
Feel free to make any reasonable offers or trades. I am looking to put a stock engine and trans back in the truck.
I can send more pictures upon request.
I bought this unit brand new and had it on my sled puller
for a little less than 4 months. This unit is nearly brand new.
$1200
(Pro Software Included)
-WIRELESS ADAPTER TO LAPTOP.
-3 RPM CHANNELS, Engine, Clutch, Driveline or Wheel Speed
-1 ACCELEROMETER CHANNEL, Forward G Meter
-12 ANALOG CHANNELS, Pressures, temps, position, Lateral G Meter, etc.
-8 EGT CHANNELS, Exhaust Gas temps, 0 -- 2400 DegF
-3 DIGITAL CHANNELS, WOT, N2O Stages, etc.
-1 BATTERY VOLTAGE CHANNEL (Internal)
-Dimensions: 2 Modules, 5" x 4" x 1" each
-INCLUDES ALL LEADS, 8 PYROs, and SENSORS.
I have a used Front Axle ARB Air Locker that was in my 06 Dodge 2500. Used twice. Comes with Air Compressor and Rocker Switches. $1000 for the whole setup or an offer I can't refuse.
Also have a rear spool. Same situation. The spool came from Randy's Ring and Pinion. $600 or an offer I can't refuse.
Water injection system from Scheid. Used it for one season on the puller. System is complete with water pump, 7 gallon water tank, injection nozzles, Simpson boost valve, all high pressure lines, manifold, fan pulley, love-joy coupling, on/off indicator light and mounting bracket for CR block. This will work with any diesel, you will just have to fab a mount for the pump if your application is other than CR Cummins. $1200 or your offer.
Compound Turbo Setup with hood stack (used). Complete kit with all parts ready to install. Comes with two TurboSmart wastegates. It is currently setup to run one on the small charger. Small charger is BorgW 66mm. Large charger is 92mm. You can see the setup in the above pictures. I can send more specific if necessary. $4500
Fully Billet Suncoast Auto Transmission with 3D Converter. Billet Input, Intermediate, Output, Front Drum and Piston, Acc Piston, Gov Piston, Rev. Piston. Currently has a fully manual valve body with OD and Lockup in every gear. We can switch out the VB if needed. $4000
105lpm Stainless Steel Injectors from I.I. fully balanced. $2500
CR Cyl Head fully ported with a beautiful valve job. Special valve seats, inconel valves, dual springs, ZZ side mount intake. I had this head mounted on a 6.7 block. Just had it checked and have paperwork for it. Will separate springs. $4000 for the whole thing.
6.7 Block 4.25 bore concrete filled with crank and main studs. Coated bearings. $2500 for the whole thing.
Also have a set of Ross Racing Pistons and rods to go along with it.
$1000
Truxxs Pulling Tires, Excellent Shape
33x12.5R18 (4)
$800
I have 2 on dually rims.
$500
I have the complete setup to turn your single wheel into a dually while keeping your stock rims on the outside to match.
$400
Bolt on weight box. Bolts into the tow hooks location.
$500
Feel free to make any reasonable offers or trades. I am looking to put a stock engine and trans back in the truck.
I can send more pictures upon request.