Recent content by 07redsled

1. Redone 5.9 head , done by old timer in western pa who's big into tractor pullers, bonded and staked seats , valves and springs done, was run for 3k on truck then I parted truck. Kept engine. 750 obo 2. 5.9 short block from original head , light valve mark in one piston, no wall damage or...

dealer installed under warranty, t-case brand new Mopar HD 48re , P/N RH159973AB. will only have miles on it from road test and drive home, can come see it with paper work and drive it if serious on deal. all new converter and all . will trade for a g56 swap , can swap all needed parts.

Ive had some issues in life and now have to sell off my 04 3500 that was a street truck that was going to be turned into a puller. Asking 4k as it sits. 12/03 build 4x4 white 3500, 12k gvw slt ,4.10 gears limited slip rear, black interior, needs door speakers i put aplines in due to the stock...

im looking at this truck and wanting to pick your guys brains. I dont know much about these 6.4s, what do you all think about this set up and what not ?http://www.cars.com/vehicledetail/detail/136237059/overview/ just found the link to this im taking it is the same truck. its at a dealer not...

parting out my 04 common rail due to bottom end damage , cp3 250 03-04 injectors new 200hp ddp nozzles, 1600 CR head bonded seats valve work and mild port work still has intake shelf. 600 fuel rail and lines 200. feed tubes 50 full g56 swap kit with 3800lbs valair clutch and hydros tcase...

Doing dual cp3 can't use the high ram looking to trade for one that fits . Need stock style or tube style or sell for 150

done with the common fail , more parts possible to come ripping motor down soon s-06 pod smarty 500, tst with rail r48 tommy guns old one(special tune) 350, ED s468 68/102 compressor 87 .90 ar t4 tight and low miles polish cover 1k relentless dual cp3 controller 250 good stock cp3 5.9 200...

I just wanted to go and say this even tho i will most likely be flamed for it but my airdog is on its second motor which just died .... I called down today and within ten minutes i had a new one coming even with a issue of my warranty card not being found . I wanted to say THANK YOU for...

i have a set of 100 hp complete injectors from II, were in truck for 5 to 7 k not much past that , looking for trade out on a bigger set say 150 to 200 hp range , let me know what you have, even be up for a nozzle swap, i have 90s and and a set of II 65lpm so im looking for the middle road

POWER HOUSE PULL 2012 - Kempton Country Fair 9/29/12 powerhouse pulls kempton pa , hope to see alot there make it a good show for once not just the same 10 trucks , looks like good weather 70 and sunny , who all is going

In need of a np271d with 29 spline for six speed , 484 505 0689 text or call thanks matt

i have a cummins cp3 part number 4929594 ,my question is what are the two ports on the back of the gear pump for one has a inward arrow and one a outward arrow, any help would be great

I have a meyer md2 mount for dodge 02 to 08 was on my truck have all but the center clevis 150bucks. Obo also have 2 new style harness's both used shoot me an offer also open to cr parts as trade CompD Mobile Device

Pulling the seats this weekend from the 06 they are the light kakiy (light tan) color and have been cover most of there life in good shape , can send pics via text or email looking to get 500 for the pair , shoot me an offer or trade for cr parts CompD Mobile Device

well the other day i pulled into a parking lot backed into my spot when, all the sudden my 04 started hammering like heavy rod knock, i shut it down fast, in fear of the worst. After getting it home i removed the valve cover to find a couple exhaust bridges blown off and the metal spacer on the...