Recent content by not enoughsmoke

So some of the older member might remember I had a 800hp 2003 over a decade ago. I sold it to move away from CR's and Low and behold I ended back up with a 2003. However this time I wanted to take a different approach. Not to go all out .But make a fun truck to drive and use. Friend of mine runs...

So last year while on vacation with the wife. We were sitting in traffic she says "I want a new car" My reply was "hell no i want my big shop before you get anything else!" To her replying "ok lets do it" Shocked as i was with her response She then proceeds to ask "how are you gonna heat it?" So...

Anyone buy Snap-on KRBC60T welding table? Looking for reviews KRBC60T Welding Workstation

o my Dad bought this 48' Raven Semi trailer in 2003-04 when scrap and aluminum prices were up. lucky for us we had a friend that owned a scrap yard and bought this before it was cut up. The trailer was completely stripped down of all steels and sold as clean aluminum. So Dad Rigged up a hay...

I am looking for a Cummins OEM Aftercooler (air to water setup ) for a 12valve VE engine let me know if you have one Thanks Chase

Truck has a fresh new motor. The pump has maxed out for stock internals,5gsk ,131 dv and 5x17 schied injectors. Stock cam,marine pistons ,t4 manifold and had a 63/73/.90 on it broke the shaft in it and now it has a 66/73/.90 and it will hit 1300 easy. The pump and crank was pinned and...

I have decide to sell my 1999 F350 fummins. Motor is a fresh rebuild motor less than 200 miles on new motor truck has 530,000 miles on it orginally truck was a 2wd,powerstroke,auto now cummins ZF6, Ford 271,01 dodge dana 80,and ford dana 50 mods Engine marine pistons STD bore STD rod and...

I have worked in a lot for different shops and along the way I have found different tools that have made a lot of jobs easier as well as quality of work. That being said i would like to see what tools everyone has used or made your shop life easier. Furick clear Tig cups and just ordered the K2...

Well I have been working alot on my shed/shop a lot this year and about to get a decent work space and try to look professional. Its a 24x48 divided into 3 sections. 24x24 shop and tear-down space 12x24 tool room and equipment and the other 12x24 is a machine shop. it not much but let me know...

I have a set of Flux 4.5 that I installed in a customers truck and he went bigger these have 1000-1500 miles on them and one has a bad solenoid complete injectors no cores needed for 04.5-07 5.9 $1500 PayPal accepted

I have got a fuel pump that looks like a waterman big brother. the fuel pump specs are 264gph at 3300rpms I am wondering if it would be enough to keep a 215 pump for a puller alive. It would be 400gph at 5000 rpms 88gph at 1100 rpms It was free and normally comes off a 3057hp v12 diesel...

So my 99 Fummins has a dodge Dana 80 rear axle.Front is a Dana 60 with unit bearings and adapters from 8x170mm to 8x6.5 lug pattern. I acquired a 95 ball joint Dana 60 set of knuckles.I already know the knuckles will swap. The superduty axle tie rods sit on top of the knuckle and OBS axle the...

Need help got a diesel friend in the area need some minor work and advice dealer want $6000 to repair his egr stuff he needs a delete done

I am posting this up for my friend.I rode past week in the truck it runs great http://www.racingjunk.com/Trucks/182125517/2002-Dodge-Ram-2500.html Thanks Chase

I have decided to put up my 1979 Ford f 150 It's has a been restored frame and running gear wise,not body 4in lift ,4 speed ,4x4, Motor is all original just fresh rebuilt with a small comp economy cam I got it and put new 35x12.50x15 mickey Thompson mtz Dual exhaust ,recover hitch ,new blower...