Recent content by Pullin' Out

Hey guys it's been a while since I have been on here but I have a Bobcat 337 mini excavator with a V2003-M-DI-TE2B engine. We took it to the dealer for service with a suspected cracked head. Indeed it was cracked, they said it was not worth repairing and wanted to slap us with a $5000 bill to...

Im not sure if this is where I need to post this but I have an ad in the for sale section and I was wanting to post more pictures. I press the reply button, type what I have to say, click manage attachments, attempt to upload my picture that has already been resized and it informs me that there...

I have a 01 Dodge pulling truck im looking to sell. The body and Chassis have 90,000 miles and is in good shape. It was my daily driver until 3 years ago when it became a dedicated puller. All the work was done by me including machine work and fabrication. The original motor was replaced for a...

I have an S475 turbo that came off my pulling truck last year. It has a clipped and protruded 2.6 billet wheel and the large turbine with a 1.32a/r and T6 flange. It was ordered new from Haisley in 2011. The bearings and compressor wheel have 10 hooks on them after its rebuild. No street miles...

I have an ARB air locker for a Dana 60. It is for 32 spline axles. It came out of my 2.6 pulling truck it has 2 seasons on it and no street miles. It comes complete with compressor, air hose, wiring harness and fittings. It can be used with a thick ring gear or a thin ring gear. It works fine...

I am updating the pulling truck this summer. s475 turbo with a billet compressor wheel clipped to 2.6, 96x88 turbine with a t-6 1.32 housing. It was rebuilt in august of last year and only has 4 to 6 hooks on it since the rebuild. $1200 Precision pt-100 water to air intercooler. Purchased in...

Can someone lead me to a good thread about putting a hole in a nv4500 bell housing for adjusting the clutch. Im getting ready to do it to mine. I remember one from a long time ago but can't find it. Please and thank you.

Hey guys I have an S475 for sale. It has a 96x88 turbine. The housing is a t-6foot with a 1.32 A/R. Both the compressor housing and the turbine housing have been ceramic coated. The bearings are tight. $550 Thanks, Rhett 816 918-7161

I have a 2001 Dodge that I have been pulling for four seasons and its time to take a break. It has 95,000 miles and the work that has been done to the truck has been done by me including the motor and machine work. I built the motor in class at the University of centeral missouri. It has 40...

How are you all getting the little timing pucks out of your adjustible pump gear? Seems like I try a new way every time and its always a pain. My last one was stuck in tight enough I actually had to tap it and use vise grips and pry bar to get it out.

We are assembling a friends 97 12v. He bought an overhaul kit from EEP. Its the Clevite branded stuff. It came with 12 piston squirters 6 long ones and 6 short ones. I know the front one is the short one and the back 5 are the long ones but the all 6 of the short squirters have a smaller oil...

I have a Spearco air to air intercooler that is out of a dedicated puller. It was bought in august of last year it has 12 hooks on it and zero street miles. Our local association banned water to air last year but water to air is now legal this year. i will be upgrading. It pressure tested good...

I turned an 01 manual into a dedicated 12v puller. Cleaning shop. I am located in western Missouri. Pictures can be sent if requested. Thanks Stock standard bore 12v pistons. good condition. $110 shiped Stock 12v cam with numbered lifters. No pits. lobes well within spec. $110 shiped 5 12v...

I have a flat tappet aftermarket cam in my cummins puller. I set the valves one cylinder at a time as I go through the firing order. (Going off the harmonic balancer.) These readings are consistent with each other every time. Out of curiosity I watched an exhaust on another cylinder as I bared...

I have a regular cab dodge with a 271 transfer case in the 2.6 class. I upgraded the rear drive line to 1480 yokes. After putting it in the truck i realized I only have about 3 1/4 inch of spline overlap on the tailshaft of the transfer case, I am worried that is not enough. The slip yoke has a...