Search results

Anyone know what Cp3 this would be? Looking at buying this 6.7 cp3 from a friend and he got it used but was told it was an Exergy 10mm pump. Judging by the marks, Exergy told me it should have an EP and some numbers on it but this has "MD 10". Wondering if it was a very early Exergy pump or if...

Put my new motor in my 06 this last fall and went ahead with a Southbend DD3600-G full ceramic clutch with hydraulic upgrade. Drained the ATF out of the trans that it had in it the last 190k (bought truck with bad motor) and filled/overfilled it with Mobil Delvac 50wt. Put about 8000 miles on...

I bought a set of nozzles for my 06 a while back from a smaller shop that I no longer deal with. Mainly because you never knew what you were getting from them. They are supposed to be Bosch 100hp nozzles and they had a bosch emblem on them. When I had the local injection shop test the injectors...

Building my 06 motor and debating what I want to do for piston cooling nozzles. I've done some research and I'm going to be running the J-jets that bolt in the block for sure since they spray into the holes in the piston and cool them better from what I've read. But I've heard of guys running...

Brand new Cummins .020" over "small bowl" pistons for 03-04 common rails. Cummins Part #4089183, all have new rings and some of the boxes are still sealed/never opened. Going with the big bowl pistons and have no use for these. Asking $300 obo for all 6. Also have a set of stock common rail...

I've been doing some searching on these cars and I am looking at buying my uncle's 2006 VW jetta TDI with the 6 speed DSG transmission. Its got just over 160,000 miles but he has had a lot of work done to it by the dealer over the years including new turbo, new timing belt, head gasket, and I...

I woke up with a wild hair this morning. Can a truck make more power in a runaway situation rather than just full throttle? Or does anyone really know? Now I know runaway is kinda scary but what exactly happens when a VE pump runs away? I've heard the governor just loses total control and just...

I have proof now.. I had my last pull of this season last night at "Weekend On the EDGE" in Ogden, Utah. Personally I think it was probably one of my best pulls if not the best so far in my pulling career. The truck spooled the turbo like I wanted, came off the line hard, and the trans finally...

Been checkin with a few shops and most have these manifolds on order but its still a few weeks out. So wanting to see if anyone has a Steed Speed T4 preferably straight flange manifold they are willing to sell? I will consider an angled flange if thats all you got, lookin to have one before Sep...

Been checkin with a few shops and most have these manifolds on order but its still a few weeks out. So wanting to see if anyone has a Steed Speed T4 preferably straight flange manifold in stock ready to ship? I will consider an angled flange if thats all you got, lookin to have one before Sep...

I've been thinkin for quite a while and am curious why no one has ever made a 8.3 cummins pull truck for a super mod? I've seen a DT466 in a truck as well as an 8v92 detroit. As far as I know the 8.3 has been a fairly good engine? If the average joe didn't know cummins engines, it'd be hard for...

Bullseye 66/71/14 turbo, 3rd gen style with 90 degree outlet. T3 flange and 4" exhaust outlet. Will bolt right up in a 3rd gen, its currently on my 1st gen though. Has adjustable drive pressure spring type waste gate, I have it set to around 50 lbs. Its been an awesome turbo but I found a S466 I...

Well its definately summer time and that means truck pulls, drag races, and dynos all over the country. I definately had the itch and have been hitting a few events so far. On June 8th I hit Adrenaline Performance's Dyno day in Shelly, Idaho and laid down 498.9hp and 998.9 ft lbs. I've been on a...

Got a friend that went with a different cam in his 3.0 p pumped 12 valve pullin truck. So he's tryin to talk me into buyin his old Hamilton 181/210 cam that was in it. Said I could still run stock pistons with it and he only had one season on the cam. I was there when he pulled it and it seemed...

Looking for any old edge chips for a 98-02 dodge. Preferably ones that dont work or have some issues. Preferably an older edge EZ that doesn't work. Will pay money for your non working chip. Have paypal. Thanks

I've got my timing gear jumped a tooth and the pump is to the head, not sure how advanced I am degree wise, but the way it sounds it sounds like its up there, probably be 25-28*, maybe more, not real sure. But what happens with this is when I am driving and get into 3rd or OD and hit about...

Out of curiosity, Who is in the top 10 VE Hp list? Most HP on fuel with twin turbos, and most hp with fuel on a single turbo? And #s using water meth or nos? I already know the names of most the VE big dogs, but don't remember exact numbers and exact setups and how they compare or what order...

I am currently swapping an 02 into a 98.5 body. The motor is an 02 I believe, the guy I bought it from said it was an 02 but I cant really read the tag well enough to tell. The EPA tag says meets 2001 emissions so its at least newer than 01. It has wires going the crank and cam sensor just like...

I've heard a lot of things on this subject and want to know whats true and whats not, and what is best for truck pulling. Right now I'm running .018" and .008 which seemed to quiet the truck down a bit and run a little crisper, but how much tighter can/should I go or is it not a good idea? One...

I swapped a built 47rh in my 1st gen a few months ago. I've got to say its the best mod yet. It has a bilet flexplate, billet triple disk converter 2200 stall, billet input, steel 5 pinion planetary, custom valve body, and some other upgrades. Right now the truck will lockup when I have it in...