can a stock 4x4 06 fit 325/60/18's? (33inch)

probably with some torsion bar adjustments, I think 6" offset would work out good.
 
325's? That'd be pretty tight. I had 285's on Moto's with 4.5 backspace, not sure on the offset. They still rubbed a little with my T-bars cranked about 3/4 the way. I've got 295s on now on H2's and they don't rub at all. i didn't have to changed anything from the motos.
 
When I used to have my 285s on 8"wide rims with 4"BS I had to crank the bars 3/4 the way up from stockt not hit. Now I have the bars 1/4 higher than stock with 285s on 8.5" rims with 4.75"BS(Hummer wheels) & don't hit at all.

Pretty much all 18" wheels are 5" or more on the BS cause they are big enough to fit over the calipers but can have issues with frame contact.
 
YEah what he^^^^ said. Prolly have to do a level kit or maybe a Cognito 4-6.
 
i run 315 stock rim 6.75 wide 5.125" back spacing.

i trimmd/ bent the pinch weld at the bottom of the cab.

there is more than enough room to run a 16x8 with a 5"BS... btw i have cranked the tb 3/4" of an inch from stock
 

Attachments

  • HPIM0059.JPG
    HPIM0059.JPG
    68.1 KB · Views: 7
  • HPIM0061.JPG
    HPIM0061.JPG
    74.9 KB · Views: 11
  • 315-1.JPG
    315-1.JPG
    73.6 KB · Views: 27
  • 315-3.JPG
    315-3.JPG
    75.1 KB · Views: 12
  • 315-6.JPG
    315-6.JPG
    71.9 KB · Views: 13
If you read the specs on the tire it is actually a 34.5 inch tall tire IIRC. It's odd the tire manufactures say they are 33"s tall but when you read the spec's diameter says 34.5" of at least close to it.
 
jneal said:
If you read the specs on the tire it is actually a 34.5 inch tall tire IIRC. It's odd the tire manufactures say they are 33"s tall but when you read the spec's diameter says 34.5" of at least close to it.
He said 325/60/18 thats 33x13, 325/65/18 is 35/13
 
Alright guys.. its my uncle that is doing it.

I made an acct that way JFlagg wouldnt have to mail me anytime something new happened..

He is wanting to run 285s, i think. On an 18x9 wheel. They have 4.5 BSing IIRC.

Will that look alright? Ohh.. he will be running a leveling kit also.

Thanks guys.
 
I have a buddy that ran those 325's nittos on a set of 18x9's and it took green keys and ALOT of trimming and they still rub while turning over hard bumps.

Definately would run a 4" lift with them
 
I have 35's on my rig with just T-bars raised up not all the way but only 2 turns from all the way. They rub very little.
 
I cleared 325's on 16x12's w/ green keys before I got my 4" lift, but I did some cuttin'.

It all depends on how brave you are with a grinder!
 
Seems to be a common fit here. I run them with a 4 inch lift on my 03 but they look small. Running 18x8.5 welds.
 
how much further will the tire stick out with that combo?

i wish it was a ZR2, then i would know all about what he could run wheel and tire wise.. lol.
 
Back
Top