Rebirth of Monster Mudder

the body is going to be Glow Orange with black fenders. I need to pick me up a pin stripping brush so I can paint the bars on the grill black after I get it painted orange.

Dad thinks I need to put a confederate flag on the roof and call it the general mudd with the color I'm painting it.
 
the body is going to be Glow Orange with black fenders. I need to pick me up a pin stripping brush so I can paint the bars on the grill black after I get it painted orange.

Dad thinks I need to put a confederate flag on the roof and call it the general mudd with the color I'm painting it.

I thought you were doing a crazy purple? Or was that a joke?
 
Well, it was going to be plum crazy purple, but the wife didn't like the color. Then I wanted it to be bright yellow. The kids didn't like that, so we spent an hour at the paint place looking through colors and 75% of us agreed on the glow orange....

12042173466_b8f78bf974.jpg
 
Last coat of primer has been shot and just finished wet sanding it with 600 grit paper. Going to go out in a little bit and start cleaning the cab so I can start getting it painted this evening after I pick my son up from the votech bus.
 
Here are some better pictures after the fog cleared some and the tape was removed

13572277354_0103427abb_b.jpg


13571911665_ab1a85ace0_b.jpg


13572292564_e12b3b46c6.jpg
 
Tonight, I spent most of my time cleaning up the big mess I had created over the last couple of weeks and hauled off the trash cans to our dumpster. But I did get the old shock brackets cut off with the cutting torch and the new tabs welded onto the axle and the cage cross bar. It's going to be a ***** getting those shocks compressed to fit in there.

I'm planning on getting the floor of the cab and the outside part of the roll bar coated in POR 15 tomorrow and work on the passenger side door as well. Tomorrow is the last day of work, then I'm on vacation through the 13th.

13593314405_7038cfc011_b.jpg


13593696054_b59e8fcbdc_b.jpg
 
Today, I washed and prepped the floor of the truck, the outside part of the roll bar and the axle part of the rear differential and got them coated in POR 15 and then a second coat on the outside pieces with Chassis black on the top of it. I also painted the remote reservoirs for the front shocks black and their holders, along with the last few pieces that needed coated like my seat mount and the radiator hold down brackets.

Worked some more on the passenger door and need to apply some more filler to get it finished out.

Also measured and marked the first piece of diamond plate aluminum for the bed. Will get it cut out somehow tomorrow.

The cab is ready to get things started on installing stuff in it at this point.

13614921854_82b99f29b9_b.jpg


13614567115_ace616d7d5_b.jpg


13614912474_e38516660f_b.jpg


13614904844_ebebb68105.jpg


13614897724_e27ccdd632_b.jpg


13614892444_270909f8d5_b.jpg


13614546093_414a96e06f_b.jpg


13614881944_d3765cec20_b.jpg


Funny thing about the sheet of diamond plate, it's 4' x 10' x 1/16". I called a couple of places in Tulsa looking for atleast a 4x8 sheet of it to make the floor of the truck. I called one place and said they would have to check to see if they had any. So I called another place that was just 2 blocks away from that place, they had a 4x10 piece for 130.00 About an hour later the other place called me back and said they had it, that it was 230.00 for a 4x10 sheet. Talk about a slight difference in price from two places within blocks from each other.
 
Today was spent running errands with just a little bit of time working on the truck. Tried putting one shock on by myself and that didn't work. Will have to get my son to help tomorrow evening. I worked on both doors, beat out the dent on the drivers side and started in with the filler on it. Passenger side is starting to look better, but still needs some work on it.
 
Spent most of the day working out in the shop when I wasn't watching all the fires around us. I will be really glad when we get some rain and puts all these fires out.

So today, while out there, I drilled the holes for the gauges in the dash. Then taped off the floor and touched up the dash where I drilled the holes and some spots I missed from when I painted the cab.

While I was waiting on that to dry, I worked on the doors, sanding them down and then added more filler to them. So I alternated between working on the doors and working on the truck.

Put the gauges in the dash, they still need to be wired. Installed the rear shocks (those were a pain to get compressed and the bolt inserted with the misalignment washers).

Installed the seat belts and the seat. As well as the floor pans for the truck.

13655411413_55efa20d5b_b.jpg


13655377735_3033d2df46_b.jpg


13655371215_6edb8fabc6_b.jpg


13655364035_fb62c0f10a_b.jpg


13655353965_327e081ea1_b.jpg


13655698954_6627a5921d.jpg
 
Finished up with the filler on both of the doors today and applied the finish glaze to them. They look much better now. Managed to get both sides of the doors primed, the header to the bed, all 4 pieces of the inner fenders I made and the power wagon emblems. While I was at it, I primed my son's radiator support for his truck as well.

In between doing all of that, I cut out the first piece of flooring for the bed and have it partially installed. I need to put a few more fasteners in to firmly hold it in place. I put the rubber molding in place for the front cowl vent and cut the pieces of welting or whatever it's called, need to figure out how to install it with the split nails to hold it. I had some left over rubber molding for the vent, so I repurposed it to cover the cutouts around the roll bars.

Tomorrow I plan on wet sanding the doors and the other parts and get them painted orange.

13682179194_63f536dbe5_c.jpg


13681817815_38d113e47b_b.jpg


13682158664_eb8281e28a_b.jpg


13682152134_e71c2f1695_b.jpg


13681828463_30a39709ce_b.jpg


13681819143_f0255aaac2_b.jpg


13682121914_58949c2727_b.jpg


13681760025_9e18727868_b.jpg


13682104304_787b59d0e5_b.jpg


13681742455_cdc430f0b5_b.jpg


13681736275_a66de2875f_b.jpg


13682082654_263ac18990_b.jpg


13682077304_b12638248b_b.jpg


13681708205_1fc2f495a8_b.jpg


13681740073_e136df25ff_b.jpg


13681690485_ae05bc07ef_b.jpg


13681685085_a25d13dfc2.jpg


13681679625_ab7fb21b8b.jpg


13682025744_5901a02e76_b.jpg


13681662475_cb09b82b7b_b.jpg
 
this project is starting to look less and less like a mud truck and more like a knobby tire cruiser.

Too clean to beat up!
 
It's one of the most photographed trucks that races in this part of the country. It's the only diesel which makes it unique and then it surprised people what the old fat pig can do. There are some guys that run total pieces of crap and you wonder how many parts they left in the pit after they went through it.

I just like trying to do things right and make a nice looking truck with weight kept in mind. That's why I went with 1/16th inch Aluminum diamond plate flooring for the bed. That was the lightest thing I could think of to put a floor in the bed with as I had to have one.

I just like building ****
The paint is single stage machinery paint.
 
Looking great! Is there a tach available with a more "diesel" like range? It seems like it'd be a little hard to quickly see rpm on a 10k rpm gauge.
 
There are tach's that have a smaller range, but they don't have shift lights either. My shift light will be mounted on the top of the dash where I can see it without looking down. I use my go pro to record the gauges during a race to help see what's going on during a run as a post analysis. I've also used the video's to determine I had a boost leak getting gradually worse over time.
 
Spent the day sanding and painting the doors and a few other odds and end while I was at it. My paint gun has been driving me nuts with the drips it was causing on what I'm painting. Think I have finally gotten that taken care of finally. I spent most of the day sanding out the drips that were on the doors and then putting two coats of epoxy on them and then two coats of orange on the top side tonight. After they dry and harden over night, I will flip them over and shoot a coat on the inside tomorrow morning.

Also started bending my brake lines to connect my master cylinder to the lower connections down on the frame to get the brakes working. Should get those finished up tomorrow.

Installed the molding around the front of the cab today, when I was in town picking up the brake lines, I picked up some small screws and used those to install the molding instead of those split nails.

I have the rear fenders primed and ready for the black once I wet sand them. The emblems are primed as well and ready for paint too.

Once I get the doors done and on the truck then I can get started on the rear bed sides. Hoping they won't take a long time, but the way everything else has gone, I'm not betting on it. I have to pick up another gallon of epoxy tomorrow, I've almost used the gallon I had.

13707149573_af35488a1b_b.jpg


13707141933_89cc64bda3_b.jpg


13707122045_fac2fb82b4_b.jpg


13707113465_c4969b24c4_b.jpg


13707467334_58dbd35673_b.jpg


13707462974_96e1edc14e_b.jpg


13707092195_e69aabbafc_b.jpg
 
Started the day off with painting the inside of the doors and the opposite side of the flat panels I had been painting too. Once they dried, I put them on the truck, had to chase down some new screws for the door handles and then tap the holes to clean them out. Passenger side door shuts good. The driver side still needs some more work. It will shut and latch most of the time, but it's still not 100%.

Started working on both of the bed sides, worked out some of the high spots and started in with filler on the outside portion to give it an overall smooth over. The drivers side is looking good and doesn't need much more work. The passenger side I just started on it, so it will be most of tomorrow working on it to get it finished. Hoping to shoot primer on them tomorrow evening.

Also today, I finished up the brake lines, and put together my air intake. I think it will work out good and also started working on the water lines to the back of the truck.

13728539193_82c2d3d813_b.jpg


13728499325_56e90ee362_b.jpg


13728492815_48f0cd5fe2_b.jpg


13728511223_501c4eeaa9_b.jpg


13728471575_0d6c735ae9_b.jpg


13728466735_ba4afe96f5_b.jpg
 
Spent the whole day just sanding on the bed sides. Finally finished both of them and was able to get the back sides primed tonight. Picked up some steel balls where my dad works rebuilding oil pumps and grabbed 4 old ones while visiting him and welded them on the ends of the rolled tops of the bed sides so that they don't fill up with mud.

Tomorrow I plan on getting the outside of the bedsides primed, wet sanded and in color. While waiting on each of those steps, I'm going to work on running the water lines and start working on the front frill section for body work. It won't take a hole lot on it to get it ready. Then all I will like is the hood and the front fenders to do body work on.

13750698865_0e9925d9ee_b.jpg
 
Back
Top