It's funny when all the emails regarding
buying the injectors go through, but when I try to contact later all of a sudden the emails dont work. If it is all a misunderstanding than I openly apologize for my screwup:
From: Brian
To: "******, Mark A" <Mark.*****@snapon.com>
Date: 04/13/2011 04:10 PM
Subject: Re: TRACKING NUMBER
I got the injectors last week. I dropped them off at my injection shop here locally
Able Fuel Injection in Lewisville, TX
Results were not what I was expecting at all. After getting them cleaned up we put them on the test stand to see where they sat and if they needed adjusting.
1st 2 popped at under 200bar... About 100 bar short, They literally just chattered and dribbled fuel. Hoping that it was just because the pop pressure was so low we tore a couple down and shimmed them up. We were not even hardly able to get the pressures up because the seal was so bad within the nozzle, they would leak down or chatter really bad and spit fuel.
Sad to say these are cores at best, bodies look to be ok, but the nozzles are trash. Hard to believe they came out of a running truck, must have been a smoky one if it even ran. Disappointed to say the least.
Brian ****
From: "******, Mark A" <Mark.*****s@snapon.com>
To: <******>
Date: 03/31/2011 09:49 PM
Subject: TRACKING NUMBER
Hey Brian,
The tracking number on your injectors is 1Z X80 75W 03 9791 8344
Thanks again, and as long as all goes as planned I will be dropping them off at UPS tomorrow.
Mark ****
Authorized Snap-On Franchisee
304-279-****
From: **** [mailto:****]
Sent: Fri 3/25/2011 11:18 AM
To: *****, Mark A
Subject: RE: Injectors
Check went in the mail yesterday, let me know if you dont see it by the end of next week.
Thanks,
Brian ****
From: "*****, Mark A" <Mark.*****@snapon.com>
To: <****>
Date: 03/24/2011 07:13 AM
Subject: RE: Injectors
I'm not set up with paypal, I'll get them sent out though as soon I get the check though.
Mark ******
Authorized Snap-On Franchisee
304-279-***
From: ***** [mailto:*****]
Sent: Wed 3/23/2011 2:42 PM
To: *****, Mark A
Subject: RE: Injectors
Any chance you have paypal or something? I could pay the fees...
Otherwise check is fine
Brian *****
From: "*****, Mark A" <Mark.****@snapon.com>
To: <*****>
Date: 03/23/2011 12:21 PM
Subject: RE: Injectors
Yeah send me a check or money order to 11064 Leetown Rd Kearneysville WV 25430 and I'll ship them out.
Mark ****
From: ***** [mailto:****]
Sent: Wed 3/23/2011 1:06 PM
To: *****, Mark A
Subject: RE: Injectors
As long as they are botsch bodies $350 shipped to 76051?
Brian ***
-----"****, Mark A" <Mark.*****@snapon.com> wrote: -----
=======================
To: <B******>
From: "****** Mark A" <Mark.*****@snapon.com>
Date: 03/23/2011 11:41AM
Subject: RE: Injectors
=======================
No and I cant remember the hole sizes, they were orginially built for a vp but there really isnt that much difference in the two pop pressures. Its mainly an advertising hype from what I collect from Van and Kent. The 6x.018 were vp and they told me that it isnt enough of a change to worry with. The JL's however did drive well as a vp, that havent been in the truck since I converted it to a P Pump. They have 5k miles on them at the most.
Mark *******
________________________________
From: ****** [mailto:*****]
Sent: Wed 3/23/2011 12:21 PM
To: *****, Mark A
Subject: RE: Injectors
Yup mainly looking for the hole size on the JLs...
Any idea what the pop is set at?
Mileage on the sticks?
Sure hate he isn't around anymore, was great guy to work with...
Brian *****
From: "****, Mark A" <Mark.****@snapon.com>
To: <****>
Date: 03/23/2011 11:17 AM
Subject: RE: Injectors
________________________________
The 10 hole II injoectors are 2 different sized holes not too sure what the sizes are, the JL are 7x.008 or 7x.010 if memory serves me correctly. The 6x.018s will be a little bigger than what your running now and are a really good competition injector. Im sure as you know, not too drive friendly to the engine.
Hope this is what you were asking for, if not send me another email.
Thanks,
Mark ****
Authorized Snap-On Franchisee
304-279-*****
________________________________
From: ****** [mailto:***** <mailto:******> ]
Sent: Wed 3/23/2011 11:12 AM
To: *****, Mark A
Subject: Fw: Injectors
currently have 7x.014... oops
Brian *****
From: Brian *****
To:
MARK.******@SNAPON.COM
Date: 03/23/2011 10:10 AM
Subject: Injectors
________________________________
Saw your ad on compd. Give me some background and sizes on the injectors you have for sale.
I have a P7100 pumped 01 with a set of JL 7X0.012, looking to downsize for a while.
What are the II injectors?
What size are the John Link 120s?
Brian *****