Recent content by BigBadDually

Hi guys, had a brand new ht60 givin to me, is there anyone fabricating a twin piping kit for a hx35/40 and ht60? Have not been able to find anything. Contacted source automotive and they didn't offer anything. Thanks for any help!

im looking to twin my truck and need to do it on a budget. so the plan was to buy a ht3b and stick it under the hx35. Now there is a brand new Rotomaster 75mm 1.34a/r with a t6 flange, i cant find any info on these turbos, what do you guys think?

Ok so today i took the #5 plate out, flipped the washers on the afc diaphragm and ground the afc foot. I took it out for a drive and i am not feeling much difference if any. Timing is at 15*, 3kgsk from pdr, its a 160 pump, i need some power.

95 auto ram, i remote start it every morning and it usually cranks for about a second and a half befor firing up, after a 10 hour shift at work i tried to remote start it and it just cranked over and over but never fired, same thing this morning except i didnt use the remote start, it wont fire...

I will start with the truck. 95 cc lb dually auto. Truck is pretty much stock, DTT Billit trans, gauges, K&N cold air, stock straight pipe into 6 inch stacks, boost elbow, 5 plate ff, afc ff, starwheel loosend, 3 gsk, 15*, 410's, 215 tires. Hate the 410 gearing. What this truck needs to do for...

So i was looking for a new camping/hunting rig and came across this. she is a 92, 5 speed, 250,000 kms, pump turned up and timing done by PDR, 10" cutom built lift by T&S suspension, custom drive shafts with huge ujoints by high angle driveline, 4.56 gears and detroit lockers, 35 spline shafts...

I am in need of a getrag, anyone got one sitting around in good shape?

how would you do it? I know it can be done, but not many people have achieved it. So i need peoples input on how i am going to do this? what pump mods? Would it be cheaper to get a good used 215 pump and have it turned up? What injectors? what delievery valves? Injector lines? fuel lines...

Here in B.C. i dont have many options for tranny builders. DTT has a shop an hour and a half from me. So who is happy with DTT trannys and what did they do to the tranny, what mods did you have done to your truck?. Who isnt happy with DTT trannys and why? Cheers.

So i pulled the trans pan off of my 95 cummins ram to install a trans temp gauge. Well while i was in there i found something i didnt want to... Lots of brass shavings. The only thing i could think of it being would be thrust washers, the truck only has 35,000 km on it and has never seen any...

I'm looking to find a dual 10" box for under the rear seat in my 95 extended cab dodge. Anyone have one? There isnt much room under the rear seat.

So it was pretty could up here in British Columbia last night, my truck sat for about 12-13 hours in -10 conditions unplugged, wasnt planning on going out this morning but when i went to start it i cranked it over and it fired up and died twice so i gave it a bit of fuel and it fired up but was...

Looking into buying a 1st gen 12v. to swap into my 82 chev. I really dont know anything about the VE pump, what can i do to get power out of this motor? Injectors obviously, exhaust, intake but what else can i do? How much power can i get out of it without spending too much? Thanks guys. :rockwoot:

I have a 95 ctd with a 47 rh. The other night i was driving down the highway at about 1800 rpm when all of a sudden for no reason it feels like the torque converter unlocked? or something and the rpm went up to about 2000 for 2 seconds and then back down to 1800 again. It did this twice in about...