Recent content by cliff-1972

I have the early AFC Live Stage 2 and been using it for over a year now.I installed it with the 21 psi full travel spring because that's what kinda spring tension is what I ran with out AFC Live.I was running a light spring set at 65 psi full travel w/a "100" plate full forward.Well,with the AFC...

Haven't posted in years,but still around.I have been running a S475 (75/96/1.32) in my compound set up (63/68/.70 secondary).I have Weston 5 x .016 injectors, Ponci benched 180 hp pump (468cc with 181 dv's has 7 mm dv's now),5k and 22 degrees timing.It has a Maxspool 2.5 cam and ported bowls and...

Like the title said.They are used,20K on them,3 re-torques and in good shape other wise.$210 shipped.Thanks,Cliff (843)437-4746

First I'll start by telling you all why I'm having to ask this question.I have had transmission issue why my E4OD for the last 4 months or so.Broke the O/D plantary splines,front pump and O/D clutches to being with.Had that fixed.I reinstalled it and 800 miles later it quite locking up the...

AD 165 used forsale.Made for 12V Cummins.Everything there minus a few fittings and some hose.All wiring and manual come with it.Changed my fuel system out to a custom built one.Want $275 plus shipping.Can text pics of it.Call (843)437-4746 Cliff

Went to Rockingham Dragway NHRDA event and dyno'ed the Fummins.It did 563hp and 936ft.lbs. torque on a Mass Diesel performance Dynojet.A little low for what I have done.The AirDog 165 is set at 40psi,but as soon as you hit the throttle it goes to 20psi or less.I had the operator pull to...

As the title states.Can the cam gear and crank gear be changed while still installed in the engine?It started like this.I was looking for the cause of a front oil leak.Was cleaning the front cover and notice it looked cracked.Not where it would normally break when the K.D.P. lets loose,but on...

I bought this new from Industrail Injection in 2011 for my compound set up.Last year I changed to a 63/68/.70.The 351CW has about 10K on it.The cover is polished and internal wastegate ported for better flow.There is no play in shaft.I would like to get $350 plus shipping for it.Call or text to...

I have three HT3B turbos forsale.All are in good shape with little end play on all of them.I don't know the exact compressor/turbine wheel size on each of them.The turbine housing sizes are 22cm open,23cm divided and 27cm divided.I would like $150 each for them plus shipping cost.You can call me...

Well to start with I suck at keeping you updated on my build.Have put a little over 30k on it sense I did the conversion.No major mishaps to speak of,other than a blown head gasket early on after install(re-torque,re-torque can't say it enough,lol).I went from what was supposed to be DDP Comp...

It has been almost 2 years sense I have gotten my truck back on the road.In the last month or so it has been taking longer to crank.When the engine is cold it cranks about the same as before,but after it comes up to operating temp. it takes longer,2-4 sec. before starting.The fuel shut was...

I have new bellowed up pipe kit for a 7.3PSD.It was bought from Blackwidow Diesel for $475 and I'll sell it for $375 plus shipping.Call Cliff @ (843)437-4746. Thank

I have a set of CPP 7X.012 injectors forsale.I had in the truck for only 5K miles.Nothing wrong with them just went with something else.I paid $490 and would like $300 with your cores or $400 without cores.These prices are shipping to the lower 49 states.You can call me at (843)437-4746.Thank you.

On my twin set up,HE351CW(stock) over S474,I am thinking the stock wastegate on the 351 is overwhelmed by the drive pressure.I have order a JGS400 V-band wastegate and plan to install it on the exhaust manifold.It will be installed where the turbine flange on exhaust manifold is,not a adapter...

Yep,as the heading said.I was trying to figure out a sluggish boost issue and was working over the phone with my pump builder on the subject.Well,we started out my sliding AFC all the way back.This didn't help to much.Today we blocked off waste gate feed,you can see where this going,and I drove...