Recent content by Cnp22

Put together some of the runs that were in my "trailer". https://m.youtube.com/watch?v=V1HUjPYtmqs&feature=youtube_gdata_player

I got bored on the iPad yesterday and made this short video of my cummins street truck. Enjoy it, hate it, love it. https://m.youtube.com/watch?v=lZfKLvIeqHE

I'm sure this has been answered a time or 2 but I haven't found the answered to my questions. I'll start with the problem. I'm spraying my truck, A LOT, and after about a year of lots of spray it finally popped the head gasket one hot summer night (the bottle pressure was finally high enough I...

This is my 95 cummins vs a stage 2 Jotech GTR he said 700hp. http://m.youtube.com/watch?v=itNS4zxVf20 Then me vs another stage 2 Jotech GTR with a 75 shot, my bottles only had about 600psi on this run were damn near empty. http://m.youtube.com/watch?v=8NEhelRiUZs

Has anybody seen this or used it? I recently got a free rebuilt hx40w, and my luck my cheap filter came apart and damaged the compressor wheel. Not really needing more that a hx40 but does this look like a good upgrade...

Would it be ok to mount my FASS in the bed with a stock tank? Or is mounting it above the fuel level a bad idea?

I gotta 91.5 intercooler auto, my 92 was hit and will be down for a while so I put my 5x16's out of it in the 91 tuned the pump home ground pin, power screw almost all the way in. Now my ? on the tranny is I want to hold about 400-450 with this truck, what TC and valve body should I go with...

Ok need some advice on my build. Just bought a long block it's .40 over, pistons are .30 down. New stock cam, crank, ect. Injection pump is a 175hp p-pump with full cuts, 4gsk Head is going to get new valve seats, 60lb valve springs, a little exhaust side porting, and cleaning. Injectors are...

Ok I just broke my 4th and final input shaft in the getrag! So a nv is going back in, now my ?s are I have the nv4500, engine plate with starter, will I need any thing else? What will i have to do about a cross member? Hydraulics are the same except the end piece right? I have a valair single...

I'm posting this for a friend. It's a 2001 ex-cab long bed 4x4 5 speed for sale or trade. It's silver metallic paint is awesome but does have some sctratchs, interior is cloth no rips or tears, new dash. Rhino lined bed. Motor mods Arp head studs New valve seats and head cleaned Hamilton big...

Iv got a 1992 ex-cab long bed 2wd 5 speed. It has a 175 p-pump with full cut dvs, 5x16 injectors, 4k gsk, 95 fass, industrial injection 66mm turbo, valair single disk ceramic, electric fans, glow shift egt and boost, I think that's it. Looking to trade for anything really would really like a...

Ok I got a $250 gift card for ARP and I have studs allready what else do they got worth getting?

I'll will be looking to buy a cam soon and need to know what one will be best for my set up. It's my daily driver and It will hit the strip quite often once it warms up. I don't tow anything anymore with it. Here's my setup it's a 1992 5 speed, 175 p-pump, full cut dv's, 5x16's, 95 fass, 19*...

How much boost will my II super phat shaft 66mm take before it starts sending parts thru the intercooler?

Iv got a bad hop when I try to go some where (in a hurry) will traction bars solve this? And also how long should they be? I have a ex-cab long bed 1st Gen. Thanks!